Bedienungsanleitung Scheppach DS200 (Seite 16 von 44) (Deutsch, Englisch, Holländisch, Französisch)

781637

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Residual risks m

The machine has been built according to the latest technology

and recognised safety rules. However, there is still a chance of

residual risks whilst working.

• Endangering health through noise.

• Endangering health through electricity, when using improperly

connecting cables.

• Additionally, despite all the safety provisions, residual risks can

occur which are not obvious.

Residual risks can be minimised by complying with the “Safety

notices”, the “Intended use” as well as operating instructions

overall.

Equipment g. A

1. Speed adjustment

2. Locking mechanism for on switch

3. Handle

4. Additional handle

5. Suction adjustment

6. Main switch

7. Dust extractor

8. Grinding plate

9. Sand paper 6 units (grain: 80, 100, 120, 150, 180, 240)

10. Flexible suction hose

11. Dust bag

12. Carrying strap

13. Replacement carbon brushes, 2 brushes

14. Screwdriver

15. Allen key

16. Connection adapter

Commissioning

Main switch and speed adjustment (Fig. 1+2)

This device is equipped with a locking mechanism for the on switch so

that the device remains on after it has been switched on.

• Switching the device on using the „On“ button: Actuate the main

switch (1) to start the electric tool

• Leaving the device switched on using the „On“ button: For conti-

nuous operation, actuate the locking mechanism for the on switch (2)

so that device continues to operate.

• Switching the device off using the „Off“ button: To switch the

device off, only briey press the main switch (1) and release it imme-

diately.

• Adjusting the speed: You can control the speed of the grinding

plate by adjusting the speed control (3).

Inserting and changing the sand paper (Fig. 3+4)

Note: Before inserting or removing the sand paper, make sure to switch

off the device and disconnect it from the power supply.

• To replace the sand paper (1), place the device on the oor. Take

the sand paper (1) and secure it on the grinding plate (2). The sand

paper (1) automatically connects to the grinding plate (2). Make sure

that the holes of the grinding plate (2) align with the holes of the sand

paper (1).

Connection set for the dust extractor

The connection piece for the dust extractor is used to connect the

device with the fabric bag. This minimises the level of dust for the

operator.

Connect the device to the suction hose (Fig. 5.1, 5.2, 5.3)

• Plug the adapter connector (1) on the vacuum cleaner connection (2)

of the machine and turn it to lock it.

• Insert the dust hose (3) into the dust extractor (4).

Connect the dust bag to the suction hose (Fig. 6.1, 6.2, 6.3, 6.4)

• Installation instructions: Insert the hose (1) into the connection piece

of the dust bag (2). Make sure that the spigot locks into place in the

connection piece of the dust bag to securely connect the hose (1)

with the dust bag (2). (Fig. 6.1, 6.2)

• Removal: Press the locked connection piece of the hose (1) together

using a screwdriver and remove the hose (1). (Fig. 6.3, 6.4)

Adjusting the suction power (Fig.7)

• Turn the suction adjustment control until the desired suction power is

achieved.

Electrical connection m

The installed electronic motor is connected and operational. The con-

nection complies with relevant VDE and DIN stipulations.

The customer’s mains connection as well as extension leads used must

comply with these provisions.

Hazardous electronic connections

Insulation damage often occurs on electric connections.

Causes include:

• Pressure marks when connections are guided through windows and

doors

• Kinks due to inappropriate attachment or guidance of the connection

• Cuts when the connection is run over

• Insulation damage when being pulled out of the wall socket

• Tears from ageing insulation

Such hazardous electric connections must not be used and are dange-

rous to life due to the insulation damage.

Regularly check electric connections for damage. Make sure the

connection is not connected to the mains when checking. Electric

connections must comply with relevant VDE and DIN stipulations. Only

use connections marked H 07 RN. Printing the type designation on the

connection is the law.

AC motor

• The power voltage has to be 230 Volt – 50 Hz.

• Extension leads up to 25 m in length must have a cross section of

1.5 mm2, at more than 25 m length, it has to be at least 2.5 mm2.

• The mains connection is protected against short circuit with a 16A

slow fuse.

Connections and repairs to the electrical equipment may only be

carried out by a trained electrician.

If there are any questions, please provide the following data:

• Motor’s type of power

• Data from the machine’s type plate

When sending back the motor, always send the entire motor unit with

switch.

Follow the safety notices!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DS200 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info