Bedienungsanleitung Scheppach EA1700H Herkules (Seite 22 von 76) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Finnisch)

781989

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

22 | GB

Warning!

Do not use petrol or cleanser.

Risk of explosion.

• Return the foam lter insert (F) and reposition the

air lter casing.

Do not run the motor without an air lter insert or

when it is damaged. This can cause motor damage.

In this case: The manufacturer is not liable for da-

mage resulting from this; the risk lies exclusively with

the user.

Spark plug Fig. 6-7

The exhaust/casing becomes very hot during opera-

tion. Wait for the motor to cool down.

NEVER touch the hot motor.

• Remove the spark plug cover (8) by removing the

screw (G) with the provided key.

• Remove the spark plug cap (H).

• Remove the spark plug (I) and check it.

• Check the insulator. In case of damage such as

cracks or chips: Replace the spark plug (I).

• Clean the spark plug electrodes with a wire

brush.

• Check the electrodes‘ gap and adjust it. Gap

0.75 mm.

• Return the spark plug (I) and tighten it with the

spark plug spanner.

• Replace the spark plug cap (H) on the spark plug

(I).

• Re-install the spark plug cover (8)

Ensure that no dirt gets into the cylinder head during

replacement.

Check the position of the spark plug (I).

• A loose spark plug (I) can damage the motor by

overheating.

• Tightening it too much can damage the thread in

the cylinder head.

The manufacturer is not liable for damage resulting

from this, the risk lies exclusively with the user.

Replacing the fuel lter Fig. 8

The felt lter (J) of the fuel lter can become clogged.

It is recommended to replace the fuel lter once every

three months in order to ensure unimpeded fuel ow

to the carburetor.

To remove the fuel lter for replacement, pull it out

through the tank ller neck using a piece of wire bent

at one end to form a hook.

10. Storage/Transport

Transport

Leave the motor to cool down before transporting the

machine or storing it indoors in order to prevent bur-

ning and re hazards.

Turn off the motor even for short distances when

changing locations during work.

Carry the auger exclusively by the handle. Do not

touch the casing (risk of burning).

When transporting the auger in a vehicle, it must be

stored safely.

The fuel tank (2) must be emptied completely befo-

re transport.

Storage

Never store an auger for longer than 30 days without

carrying out the following steps.

Follow the cleaning instructions and maintenance in-

structions before storing the device!

Storing the auger

If you store an auger for longer than 30 days, it must

be prepared ahead of time. Unless the storage ins-

tructions are followed, fuel remaining in the carbu-

retor will evaporate, leaving gum-like deposits. This

could lead to difcult starting and result in costly re-

pairs.

• Remove the fuel tank cap slowly to release any

pressure in tank. Carefully drain the fuel tank.

• Start the engine and let it run until the engine

stops in order to remove the fuel from the carbu-

rettor.

• Allow the engine to cool (approx. 5 minutes).

• Remove the spark plug.

• Pour 1 teaspoon of clean 2-cycle oil into the com-

bustion chamber. Pull starter rope slowly several

times to coat internal components. Replace spark

plug.

• Store the auger in a dry location, far away from

potential sources of ignition, such as furnaces, hot

water boilers with gas, gas dryers, etc.

Recommissioning the auger

• Remove spark plug.

• Pull starter rope briskly to clear excess oil from

combustion chamber.

• Clean the spark plug and check that the electrode

gap is correct.

• Prepare unit for operation.

• Fill fuel tank with proper fuel / oil mixture.

11. Service information

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables..

Wear parts*: spark plug, drill

* Not necessarily included in the scope of delivery!

12. Disposal and recycling

The equipment is supplied in packaging to prevent

it from being damaged in transit. The raw materials

in this packaging can be reused or recycled. The

equipment and its accessories are made of various

types of material, such as metal and plastic. Never

place defective equipment in your household refuse.

The equipment should be taken to a suitable collec-

tion center for proper disposal. If you do not know the

whereabouts of such a collection point, you should

ask in your local council ofces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach EA1700H Herkules Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info