Bedienungsanleitung Scheppach Forsa 3.0 (Seite 24 von 48) (Deutsch, Englisch)

782262

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Noise data

Measurement conditions per EN 1870-1: 1995-07; DIN EN ISO

11202; DIN EN ISO 3746

The stipulated values are emission values and so do not necessa-

rily represent safe working values. Although there is a correlation

between emission levels and exposure levels, it is not possible

to reliably determine whether additional protective measures will

be required or not based on this. Factors that could inuence the

exposure level present at any given time in the work area include

the duration of exposure, the nature of the working area, other

noise sources etc. e.g. the number of machines and neighbouring

processes. The permissible workstation values can also vary from

country to country. However, this information should enable the

operator to better evaluate the hazards and risks.

Sound power level in dB

Idle LWA = 91.2 dB(A),

Working LWA = 97.7 dB(A)

Sound pressure level at workstation in dB

Idle LpAeq = 80.6 dB(A),

Working LpAeq = 87.6 dB(A)

A measurement uncertainty supplement applies to the emissions

values stated:

K = 4 dB.

Dust emission details

With the connection of the machine to a properly working suction

device which has a minimum suction ow rate of 20 m/s at the

suction nozzle, it can be assumed that the dust emissions will

remain permanently below the value of 2 mg/m3 overall dust at the

machine workstation.

General information

1. After unpacking check all parts for transport damage. In the

event of complaints the carrier must be informed immediately.

2. Later claims will not be recognised.

3. Check whether the shipment is complete.

4. Familiarise yourself with the product by means of the opera-

ting instructions before using for the rst time.

5. With accessories as well as wearing parts and replacement

parts use only original scheppach parts. Replacement

parts can be obtained from your dealer.

6. When ordering please provide our article number as well

as type and year of manufacture for your equipment.

Note

In accordance with the applicable product liability laws, the ma-

nufacturer of the machine assumes no liability for damage to the

machine or caused by the machine arising from:

1. Improper handling.

2. Failure to comply with the operating instructions

3. Repairs carried out by third parties, unauthorised specialists.

4. Integration and exchange of „Non-original scheppach replace-

ment parts“.

5. Use other than that as stated in „Proper use“

6. Failure of the electrical system in the event of the electrical

regulations and VDE provisions 0100, DIN 571 13 / VDE 01 13

not being observed.

Our recommendation to you:

Read the whole text of the operating instructions before

assembly and start up.

These operating instructions should help to familiarise you with

the machine and to use it for its intended purpose. The operating

instructions include important instructions for the safe, proper and

economic operation of the machine, for avoiding danger, for mini-

mising repair costs and downtimes and for increasing the reliability

and extending the service life of the machine.

In addition to the safety instructions in these operating instruc-

tions, you must also observe the regulations applicable to the

operation of the machine in your country.

Keep the operating instructions safely at the machine in a plastic

sleeve, protected from dirt and moisture. They must be read and

carefully observed by all operating personnel before starting the

work. The machine may only be used by personnel who have

been trained to use it and who have been instructed with respect

to the associated hazards. The required minimum age must be

observed. In addition to the safety instructions in these operating

instructions and the separate regulations of your country, the ge-

nerally recognised technical rules relating to the operation of wood

processing machines must also be observed.

We have marked points in these operating instructions that

impact your safety with this symbol: m

Safety instructions m

General

• Pass the safety instructions on to all persons who work on the

machine.

• Only operate the machine when it is in a fault-free technical

condition.

• The machine must only be used appropriately and in compli-

ance with the operating instructions in full knowledge of the

safety and hazards.

• Observe all safety information and hazard warnings on the

machine.

• Ensure that all of the safety and hazard warning signs on the

machine are complete and in legible condition.

• Never use the saw to cut rewood.

• Keep children away from the mains connected machine.

• The operating personnel must be at least 18 years of age.

Training personnel must be at least 16 years of age but may

only work on the machine under supervision.

• Personnel working on the machine must not be distracted.

Before start up

• Check the mains supply cables and do not use faulty cables.

• Ensure that the machine is standing on level and rm ground.

• Check the braking time to bring the saw blade to a standstill

daily. It must be max. 10 seconds. Otherwise do not continue

to work with the machine.

• Ensure adequate lighting at the workstation.

Start up

• Caution when working: Risk of injury for ngers and hands

due to the rotating cutting tool.

• Keep the machine operating station free of chippings and

wood waste

• If a second person is working on the panel sizing saw in order

to remove cut workpieces, the machine must be equipped with

DGB

Scheppach Forsa 3.0 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info