Bedienungsanleitung Scheppach FORSA 4.1 (Seite 20 von 44) (Deutsch, Englisch)

781492

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

20 english

- refer to the numbers imprinted on the riving knife. The

riving knife should never be thinner than the body of the

saw blade or thicker than the cutting joint width.

• Lower the suction hood onto the workpiece during every

working cycle.

• The hood must be positioned horizontally above the saw

blade during every working cycle.

• Always use the push-stick when cutting narrow

workpieces (less than 120 mm in width) lengthwise.

• Switch off the machine during troubleshooting or to

remove jammed pieces of wood. Disconnect power

supply plug!

• Wear close-ﬁtting garments. Do not wear jewelry, rings or

wrist-watches.

• Check direction of motor and tool rotation (refer to

"Electrical Connection").

• Machine safety equipment should not be detached or

disabled under any circumstances.

• The motor must be switched off during any conversion,

adjustment, measurement and cleaning work to the

machine. Disconnect the power supply plug and wait

until the rotating saw has come to a complete stop.

• Switch off the machine before remedying faults.

Disconnect power supply plug!

• The machine must be connected to a dust extractor at

all times during use. Follow the instructions for proper

use.

• All safety equipment and hoods must be installed to

operate the machine.

• Prior to initial operation the machine must be connected

to a dust extractor by means of a ﬂexible, non-ﬂammable

suction hose.

• The dust extractor should switch on automatically when

the panel sizing circular saw is activated.

• Switch off the motor when leaving the work area.

Disconnect power supply plug!

• Always disconnect the machine from all external power

sources before moving it, no matter how slightly!

Reconnect the machine to the power supply before

restarting the machine!

• Installation, repair and maintenance work on the

electrical equipment should be done by qualiﬁed

electricians only.

• All safety equipment and protective devices must be

reattached as soon as repair and maintenance work has

been completed.

Proper Use

• This machine complies with the applicable EC machine

guideline.

• This machine has a work area located in front of the

machine to the left or right of the saw blade.

• To prevent accidents the work area and the area around

the machine must be clear of any foreign objects which

could interfere with machine operation.

• Workpieces should not contain any foreign objects such

as nails or screws.

• Prior to initial operation the machine must be connected

to a dust extractor by means of a ﬂexible, non-ﬂammable

suction hose.

• For use in closed spaces the machine must be connected

to a dust extractor. Use a ha 3200 or ha 2600 dust

extractor to extract wood shavings or sawdust. The ﬂow

rate at the suction connection piece should be 20 m/s.

Partial vacuum 1200 Pa.

• The automatic switch on device is available as a special

accessory.

Type ALV 2 Art. No. 7910 4010 230 V/50

Type ALV 10 Art. No. 7910 4020 400 V/50

When the machine is switched on the dust extractor

switches on automatically after a 2 - 3 second time

delay. This prevents overstress to the house fuse.

After the machine has been switched off the dust

extractor continues to run for 3 - 4 seconds before

switching off automatically.

This ensures that residual dust is extracted in accordance

with the hazardous materials ordinance. This conserves

electricity and reduces noise. The dust extractor runs

only when the machine is in operation.

For industrial work use the rg 4000 dust extractor.

Do not switch off or remove dust extractors when the

machine is in operation.

• The panel sizing circular saw is designed for use in

processing wood or wood-like materials only. Use genuine

parts and accessories only. Select the correct saw blade

according to type of cut and type of wood (solid wood,

plywood or particle board) in accordance with EN 847-

1. Refer to the special accessories list.

• The manufacturer shall not be held liable for improper

use!!

Additional Hazards

This machine is designed in accordance with state of the

art technology and accepted standards of technical safety.

In spite of this certain additional hazards may occur during

operation of this machine.

• Risk of injury to ﬁngers and hands from rotating saw or

workpiece if saw or workpiece is routed improperly.

• Risk of injury from rotating saw resulting from improper

mounting or guide control or from operation without end

stop.

• Health risks due to excessive noise. Permissable noise

levels are exceeded during operation of the machine.

Always wear ear protection.

• Risk of injuries from defective saw blade. Check blade

condition regularly.

• Electrical hazards if improper connection cables are

used.

• In spite of all safety precautions instituted additional

unforseeable hazards may occur.

• To minimize the risk of additional hazards follow all

"safety instructions", instructions for "proper use", and

operating instructions carefully.

Special accessories

Art. No.

Workpiece holder 5472 0702

Cross table with telescopic arm 5472 0704

Cross table with telescopic arm 5472 0705

SUVA exhaust device 5472 0707

Automatic switch on device ALV 2 7910 4010

Automatic switch on device ALV 10 7910 4020

Table extension 7901700701

Scheppach FORSA 4.1 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info