Bedienungsanleitung Scheppach GS60 (Seite 23 von 64) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

781393

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 23

3. Installing den collection box (Fig. G)

• Place the locking mechanism (13) on the collection

box (8) in its lowest position (Fig. G).

• Push the collection box fully into the frame.

• Press the locking mechanism (9) on the collection

box (8) back into its highest position (Fig. I).

9. Operation

Warning! The shredder can only be started if

the collection box (8) has been pushed into the

frame and the locking device (9) is in the upper

position.

Control panel (Fig. B)

• On switch (2): Pressing this button starts the

shredder.

• Off switch (3): Pressing this button stops the

shredder.

• Switch for roll rotation direction (11):

• Button „▲“ - anti-clockwise: When this button is

pressed, the blade cylinder rotates anti-clockwise.

This is necessary when jammed shredding materi-

al needs to be freed. This function is only available

when the shredder is in operation.

• Button „▼“ - clockwise: This button switches the

direction of the blade cylinder from anti-clockwise

back to clockwise.

• Reset-switch (12): Overload protection

Working with the shredder

Alternating with branches, shred withered gar-

den waste and branches that have been stored

several days to prevent the shredder from be-

coming blocked.

• Make sure the collection box (8) is pushed into the

frame correctly and the locking device (9) is in the

upper position.

• Connect the shredder to the power supply.

• Turn the shredder on by using the on switch (3).

• Fill shredding material into the feed hopper and it

will be drawn in.

• Caution: If the material becomes jammed, rst

press the red off switch (3) to stop the device. Push

the switch for roll rotation direction (11) downwards

to the “ = “ sign. Start the device by pressing the

green on switch (2). Stop the device by pressing

the red off switch (3). Remove the jammed material.

Push the switch (11) to the “ - “ sign. The device is

ready for operation.

• Make sure the shredder has completely shred-

ded the input material before adding new.

• Do not use your hands to push in more shredding

material. Use the special pushing device (c) or oth-

er shredding material.

• When you have nished working with the shredder,

turn it off and disconnect it from the mains.

Emptying the collection box

• Stop the shredder using the off button (3).

• Set the locking device (9) to the lowest position.

• Pull out the collection box (8) and empty it.

• Re-insert the collection box (8) and push the lock-

ing device (9) up again.

Setting the counter blade

The counter blade and the blade cylinder have

been ideally adjusted by the manufacturer.

Re-adjusting the counter blade is only required if

it becomes worn. For maximum performance, it

is necessary that the distance between the coun-

ter blade and blade cylinder is about 0.50 mm.

• Turn the shredder on.

• Turn the adjustment wheel (5) clockwise until you

can hear slight grinding sounds.

• When turning the adjustment wheel (5) clockwise

by half a turn, the blade cylinder is positioned clos-

er to the counter blade by 0.50 mm.

WARNING: If the shredder blade touches the

counter blade, it will be trimmed and small pieces

of swarf may fall out of the ejection opening. This

is not an error, but it has to be re-adjusted to the

required degree because otherwise the counter

blade will wear too early.

Overload protection

In the event of overload, e.g. due to branches that are

too thick, the equipment automatically switches off.

After a short cooling period (approximately 5 min-

utes), press the reset switch (12).

10. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions. The

customer‘s mains connection as well as the ex-

tension cable used must also comply with these

regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach GS60 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info