Bedienungsanleitung Scheppach HA 3210 (Seite 7 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

782121

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

english 7

unit must not be allowed to use it.

• Following the accident prevention and ﬁre safety regula-

tions.

• Earth the PU hose on the connection port of the ma-

chine to which the extraction unit is connected to con-

duct away the static electric charge (expose the coil in

the hose and make a conductive connection).

• When replacing the ﬁlter or chips sack, wear a dust pro-

tection mask (ﬁlter mask with particle ﬁlter, ﬁlter class

2).

 Proper Use

The machine meets the currently valid EU machine directive.

• The manufacturer’s safety, operation and maintenance

instructions as well as the technical data given in the

calibrations and dimensions must be adhered to.

• Relevant accident prevention regulations and other gen-

erally recognized safety and technical rules must also be

adhered to.

• The machine may only be used, maintained or repaired

by trained persons who are familiar with the machine

and have been informed about the dangers. Unauthor-

ized modiﬁcations of the machine exclude a liability of

the manufacturer for damages resulting from the modiﬁ-

cations.

• The machine is intended for use only with original spare

parts and original tools from the producer.

• Any other use is considered to be not intended. The

manufacturer excludes any liability for resulting dam-

ages, the risk is exclusively borne by the user.

 Remaining hazards

The machine has been built using modern technology and

in accordance with recognized safety rules.

Some hazards, however, may still remain.

• The use of incorrect or damaged mains cables can lead

to electrical injuries.

• Although having regarded all considerable rules there

may still remain not obvious remaining hazrds.

• Minimize remaining hazards by following the instruc-

tions in ”Safety Rules”, ”Use only as authorized” and in

the entire operating manual.

Equipment, Fig. 1

1 Modular casing

2 Side parts left/right

3 Floor plate

4 Wheels

5 Steering rollers

6 Filter holding arm

7 Filter

8 Filter holding tape

9 Chip bag

10 Tension belt

11 Spiral hose

12 Accessory bag

13 Operating instructions

Assembly instructions

Wheel assembly

Bolt steering rollers onto ﬂoor plate using 3 hexagon bolts

M6 x 10 mm and nuts M6 each. Bolt wheel brackets onto

ﬂoor plate. Fasten wheel axle with wheels and wheel pins.

Put hub cap in place.

Base assembly, Fig. 3

Bolt left and right side parts together using 3 hexagon

bolts M6 x 10 and nuts M6. Place them onto the ﬂoor

plate and bolt them together with 4 hexagon bolts M6 x 10

mm, and at the side with 4 countersunk screws M6 x 20

mm and nuts M6.

Casing assembly, Fig. 4

Place the modular casing onto the fully assembled base

and fasten it wih 4 hexagon socket screws M6 x 18 mm

and 6 screws recessed head 5 x 35 mm.

Filter holding arm, Fig. 5

Fix the ﬁlter holding arm to the modular casing.

Filter assembly, Fig. 6 + 7

Pull the ﬁlter over the connection piece and fasten it with

ﬁxing tape.

Tighten the worm drive screw using a slotted screw driver.

Insert the ﬁlter holding arm into the eye of the ﬁlter.

Chip bag with tension belt, Fig. 8

Turn the chip bag from the inside upside down by approx.

20 mm and pull it over the connection piece of the casing.

Then tighten the tension lock.

PU hose with wire hose clip, Fig. 9

Push the suction hose with hose clip onto the suction con-

nection piece and tighten the clip with a screw driver.

Operation and maintenance

General:

The dust extractor unit has been designed for the extrac-

tion of dry dust and chips of the dust classes G and C (ﬁlter

C = accessory).

• Necessity of cleaning dictated by the amount of dust

(decrease of suction capacity).

• Replace chip bags in time.

• Only use original chip bags.

• From time to time, check the turning direction by com-

paring the motor cooling fan in the slowing-down phase

with the direction arrow. A wrong direction of revolution

reduces the suction capacity and warms up the motor

excessively. The direction of revolution may only be

changed by an authorized electrician.

Note:

At least once a month, an instructed person must execute

a dust examination checking

• the ﬁlter for any damage,

• the casing and the seals of ﬁlter and chip bag for tight-

ness, and

• the electrical equipment (switch-plug combination, con-

necting cable) for perfect condition.

• In no way may defective ﬁlters be used.

Electric connection

Fig. 10-12

The electric motor has been installed ready for use. The

connection meets the German standards VDE and DIN.

The connection in the customer‘s workshop must also

meet these standards.

Installations, repairs and maintenance works on the elec-

tric system may only be executed by an electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HA 3210 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info