Bedienungsanleitung Scheppach HC52dc (Seite 38 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Finnisch)

762978

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

38 GB

7. Before starting the equipment

Before you connect the equipment to the mains supply

make sure that the data on the rating plate are identical

to the mains data.

• Check the equipment for damage which may have

occurred in transit. Report any damage immediately

to the transport company which was used to deliver

the compressor.

• Install the compressor near the point of consumption.

• Avoid long air lines and supply lines (extension ca-

bles).

• Make sure that the intake air is dry and dustfree.

• Do not install the compressor in a damp or wet room.

• The compressor may only be used in suitable rooms

(with good ventilation and an ambient temperature

from +5 °C to 40 °C). There must be no dust, acids,

vapors, explosive gases or inammable gases in the

room.

• The compressor is designed to be used in dry rooms.

It is prohibited to use the compressor in areas where

work is conducted with sprayed water.

• The oil level in the compressor pump has to be

checked before putting the equipment into operation.

8. Attachment and operation

m Important!

You must fully assemble the appliance before using it

for the rst time!

You will require the following tools for assembly and in-

stallation: 2 x open-ended wrench size 19 mm (not in-

cluded)

You will require the following tools for assembly and in-

stallation: 2 x open-ended wrench size 14 mm (not in-

cluded)

8.1 Fitting the wheels (Fig. 5)

• Fit the supplied wheels (11) as shown.

8.2 Fitting the supporting foot (2x)(Fig. 6)

• Fit the supplied supporting foot (2x) as shown.

8.3 Fitting the air lter (2x)(Fig. 7,8)

• Remove the transportation stop (A) and screw the air

lter (14) to the equipment.

8.4 Changing the transportation cover (B) (Fig. 9,10)

• Remove the transportation cover from the oil lter

opening (19) and insert the supplied oil sealing plug

(15) into the oil ller opening.

8.5 Mains connection

• The compressor is equipped with a mains cable with

shock-proof plug. This can be connected to any 230-

240V ~ 50 Hz shock-proof socket.

• Before you use the machine, make sure that the

mains voltage is the same as the operating voltage

(see the rating plate).

• Long supply cables, extensions, cable reels etc.

cause a drop in voltage and can impede motor start-

up.

• At low temperatures below +5°C, sluggishness may

make starting difcult or impossible.

8.6 ON/OFF switch (Fig. 2)

• Pull the ON/OFF switch (16) upwards to switch on the

compressor. To switch off the compressor, press the

ON/OFF switch down.

8.7 Setting the pressure (Fig. 1,3)

• Use the pressure regulator (5) to set the pressure on

the pressure gauge (4).

• The set pressure can be drawn from the quick lock

coupling (3).

• The vessel pressure can be read off the pressure

gauge (6).

• The vessel pressure is drawn from the quick lock cou-

pling (7).

8.8 Setting the pressure switch (Fig. 1)

• The pressure switch (2) is set at the factory. Cut-in

pressure approx. 6 bar Cut-out pressure approx. 8

bar.

8.9 Overload switch (Fig. 14)

The motor is tted with an overload switch (18). If the

compressor overloads, the overload switch switches off

the equipment automatically to protect the compressor

from overheating. If the overload switch triggers, switch

off the compressor using the ON/ OFF switch (16) and

wait until the compressor cools down. Then press the

overload switch (18) and restart the compressor.

9. Electrical connection

The electrical motor installed is connected and ready for

operation. The connection complies with the applicable

VDE and DIN provisions.

The customer‘s mains connection as well as the exten-

sion cable used must also comply with these regula-

tions.

• The product meets the requirements of EN 61000-

3-11 and is subject to special connection condi-

tions. This means that use of the product at any

freely selectable connection point is not allowed.

• Given unfavourable conditions in the power supply

the product can cause the voltage to uctuate tem-

porarily.

• The product is intended solely for use at connection

points that

a) do not exceed a maximum permitted supply im-

pedance “Z” (Zmax = 0.382 Ω), or

b) have a continuous current-carrying capacity of

the mains of at least 100 A per phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to oper-

ate the product meets one of the two requirements,

a) or b), named above.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HC52dc Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info