www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
18 І GB
• It is recommended that you maintain the correct
operating position every time you use the machine
by placing one hand on the pistol and the other on
the lance.
• Never direct the water jet toward electrical lines or
the machine itself.
• It is normal for the pump to leak a little; this is nec-
essary to avoid damage to the pump when it is at
a standstill.
• Never use the equipment in potentially explosive
areas under any circumstances!
• The operating temperature must be between +5
and + 40°C.
• Do not cover or modify the lance or the spray noz-
zles in any way.
• The high-pressure cleaner is designed to be used
with cold or lukewarm water (max. 40°C); higher
temperatures can damage the pump.
• Do not use water that is dirty, gritty or contains any
chemical products, as these could impair operation
and shorten the life of the equipment.
Assembly
Device assembly (g. 2)
Attach the lance holder (8) and the cable holder (4)
onto the side of both fastening points on the device.
Push the handle with hose reel (1) onto the fastening
points at the top of the device and secure using the
two screws provided (length 20 mm)
Fit the wheel cover (6) using the screws provided
(length 13 mm)
Hose reel (Fig. 1)
The hose reel facilitates the space-saving storage of
the high pressure hose (3).
With the aid of the crank handle (2), it is possible to
wind the high pressure hose (3) onto the hose reel.
Important note! In order to use the high pressure
cleaner it is necessary to fully unwind the high pres-
sure hose.
Water supply connection (Fig. 1)
Screw the connection for the water supply (11) onto
the device. The connection for the water supply (11)
features a connection for standard hose coupling
systems. Attach the hose coupling of the supply hose
(min. Ø 1/2“/ approx. 13 mm) onto the connection for
the water supply (11).
Always use an enhanced water hose with an in-
dustry-standard coupling for the water supply. The
length should be at least 6.0 m. (not included in the
scope of delivery)
A backow prevention device must be installed be-
tween the drinking water and the high-pressure
cleaner! Ask your plumbing expert about this.
Technical data
Mains voltage 220-240 V~ / 50 Hz
Power input 2200 W
Working pressure 11 MPa
Nominal pressure 16.5 MPa
Delivery rate 6,3 l/min
Max. water inlet pressure 0.4 MPa
Protection class II
Danger!
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 60335.
LpA sound pressure level 81 dB(A)
KpA uncertainty 3 dB(A)
LWA sound power level 98 db(A)
KWA uncertainty 3 dB(A)
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60335.
Vibration emission value ah ≤ 2,5 m/s2
The specied vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specied value in excep-
tional circumstances.
The specied vibration value can be used to compare
the equipment with other electric power tools.
The specied vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Before putting the machine into opera-
tion
Correctly using the device
• The high-pressure cleaner must be set on a level,
stable surface..
