Bedienungsanleitung Scheppach HCE2550 (Seite 18 von 84) (Deutsch, Englisch, Französisch, Italienisch)

782028

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

18 І GB

• Never direct the water jet toward electrical lines or

the machine itself.

• It is normal for the pump to leak a little; this is nec-

essary to avoid damage to the pump when it is at

a standstill.

• Never use the equipment in potentially explosive

areas under any circumstances!

• The operating temperature must be between +5

and + 50°C.

• Do not cover or modify the lance or the spray noz-

zles in any way.

• The high-pressure cleaner is designed to be used

with cold or lukewarm water (max. 50°C); higher

temperatures can damage the pump.

• Do not use water that is dirty, gritty or contains any

chemical products, as these could impair operation

and shorten the life of the equipment.

Assembly

Device assembly (g. 4)

Push the handle (1) onto the fastening points at the

top of the device and secure using the two screws

provided (length 20 mm)

Water supply connection (Fig. 2)

Screw the connection for the water supply (10) onto

the device. The connection for the water supply (10)

features a connection for standard hose coupling

systems. Attach the hose coupling of the supply hose

(min. Ø 1/2“/ approx. 13 mm) onto the connection for

the water supply (10) .

Always use an enhanced water hose with an in-

dustry-standard coupling for the water supply. The

length should be at least 6.0 m. (not included in the

scope of delivery)

A backow prevention device must be installed be-

tween the drinking water and the high-pressure

cleaner! Ask your plumbing expert about this.

Suction from open tanks/containers and natural

bodies of water

Use a special self-suction accessory (not included

with delivery / available from dealer)

With this accessory, the high-pressure cleaner can

take in water 0.5 m above the water level. This can

last about 25 to 50 seconds.

Immerse the accessory’s hose completely under wa-

ter to drive the air out of the hose.

Connect the accessory’s hose to the high-pressure

cleaner, and make sure that the suction strainer re-

mains under water.

Let the high-pressure cleaner run with the spray gun

removed until the water ows evenly out of the high-

pressure hose.

If no water comes out after 25 to 50 seconds, switch

off and check all connections.

Once the water is owing, turn off the high-pressure

cleaner and connect the spray gun and spray lance

to start work.

Technical data

Mains voltage 230-240 V~ / 50 Hz

Power input 2400 W

Working pressure 12 MPa

Nominal pressure 18 MPa

Delivery rate 5.5 l/min

Max. water inlet pressure 0.4 MPa

Protection class II

Danger!

Sound and vibration

Sound and vibration values were measured in ac-

cordance with EN 60335.

LpA sound pressure level 78 dB(A)

KpA uncertainty 3 dB(A)

LWA sound power level 94 db(A)

KWA uncertainty 3 dB(A)

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions)

determined in accordance with EN 60335.

Vibration emission value ah ≤ 2,5 m/s2

The specied vibration value was established in ac-

cordance with a standardized testing method. It may

change according to how the electric equipment is

used and may exceed the specied value in excep-

tional circumstances.

The specied vibration value can be used to compare

the equipment with other electric power tools.

The specied vibration value can be used for initial

assessment of a harmful effect.

Keep the noise emissions and vibrations to a

minimum.

• Only use appliances which are in perfect working

order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Before putting the machine into opera-

tion

Correctly using the device

• The high-pressure cleaner must be set on a level,

stable surface..

• It is recommended that you maintain the correct

operating position every time you use the machine

by placing one hand on the pistol and the other on

the lance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HCE2550 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info