Bedienungsanleitung Scheppach HCE2600 (Seite 21 von 84) (Deutsch, Englisch, Französisch)

782033

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 21

• The product is exclusively intended for use at con-

nection points that have a continuous current-car-

rying capacity of at least 100 Ampere phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to oper-

ate the product meets the specied requirements.

9. Operation

The equipment consists of an assembly with a pump,

which is encased in a shock absorbing housing. The

equipment comes with a lance and a non-slip gun (for

an optimal working position), whose shape and con-

guration comply with the applicable regulations.

Commissioning:

Once you have completely assembled the high-pres-

sure cleaner and all connections have been made,

proceed as follows:

Turn on the water supply. Unlock the pistol (13) via

the locking switch (C). Pull back the trigger lever (D)

so that the air in the device can discharge. (Fig. 4)

Switch on the device by setting the on/o󰀨 switch (4)

to “ON”. Next, press the trigger lever (D). (Fig. 1/4)

To switch o󰀨, release the trigger lever (D), and the

device switches to stand-by. The high-pressure

cleaner starts again when you press the trigger le-

ver (D). (Fig. 4)

To switch o󰀨 the high-pressure cleaner completely,

set the on/o󰀨 switch (4) to “OFF”. (Fig. 1)

Cleaner container (9)

Fill the cleaner container with the corresponding

cleaner. The beam width can be adjusted at the noz-

zle.

Using the attachments (g. 1):

Terrace cleaner (12): For cleaning oor and wall sur-

faces.

Turbo nozzle (15): For eliminating stubborn dirt.

Nozzle (16): For coarse cleaning work.

Rotating brush (17): For surface cleaning

Cleaning brush (18): For surface cleaning.

90° turbo nozzle (19): For car underbody and gut-

ter cleaning.

Kärcher adapter (20): Use this adapter to attach

Kärcher brand accessories.

A backow prevention device must be installed be-

tween the drinking water and the high-pressure

cleaner! Ask your plumbing expert about this.

Suction from open tanks/containers and natural

bodies of water

Use a special self-suction accessory (not included

with delivery / available from dealer).

With this accessory, the high-pressure cleaner can

take in water 0.5 m above the water level. This can

last about 25 to 50 seconds.

Immerse the accessory’s hose completely under wa-

ter to drive the air out of the hose.

Connect the accessory’s hose to the high-pressure

cleaner, and make sure that the suction strainer re-

mains under water.

Let the high-pressure cleaner run with the spray gun

removed until the water ows evenly out of the high-

pressure hose.

If no water comes out after 25 to 50 seconds, switch

o󰀨 and check all connections.

Once the water is owing, turn o󰀨 the high-pressure

cleaner and connect the spray gun and spray lance

to start work.

High-pressure hose connection (g. 3/4)

Connect the high-pressure hose (2) to the connec-

tion for the high-pressure hose (6). Remove the pro-

tective cover rst.

Insert the other end of the high-pressure hose (2)

into the pistol connection (13).

To remove the high-pressure hose (3), press the but-

ton Taste (A) and pull it out.

Connecting the attachments (g. 5)

To mount attachments 14, 17, 18, 20 press them into

the pistol (13) and turn them until the lock.

To mount attachments 12, 15, 16, 19, 21insert these

into the attachment (14) and turn them until they lock.

Electrical connections

• Before you connect the appliance to the mains sup-

ply make sure that the data on the rating plate are

identical to the mains data.

• If you use any extension cables, make sure that

they are suitable for outdoor use and have large

enough wires:

1–10 m: 1,5 mm2

10–30 m: 2,5 mm2

• Plug the mains plug on the power cable into the

mains socket outlet.

• The product meets the requirements of EN 61000-

3-11 and is subject to special connection condi-

tions. This means that use of the product at any

freely selectable connection point is not allowed.

• Given unfavourable conditions in the power supply

the product can cause the voltage to uctuate tem-

porarily.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HCE2600 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info