Bedienungsanleitung Scheppach HL400CH (Seite 22 von 48) (Deutsch, Englisch, Französisch, Italienisch)

781965

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

10.1 Checking the oil level (Fig. 15)

The hydraulic unit is a closed system with oil tank, oil

pump and control valve. Check the oil level regularly

before every use. Too low an oil level can damage

the oil pump. If the oil level is at the lower notch, then

the oil level is at a minimum. Should this be the case,

oil must be immediately added. The upper notch in-

dicates the maximum oil level. The machine must

be on level ground. Screw in the oil dipstick fully, to

measure the oil level.

10.2 Ventilation screw

Before operating your machine, the bleed screw (7)

should be loosened by some rotations until air can go

in and out of the oil tank smoothly. Failed to loosen the

bleed screw will keep the sealed air in hydraulic sys-

tem being compressed after being decompressed.

Such continuous compression/decompression will

blow out the seals of the hydraulic system and cause

permanent damage to your machine.

Before moving your machine, make sure the bleed

screw is tightened to avoid oil leaking from this point.

10.3 Splitting logs

Only split logs that have been sawn off straight. To do

this, proceed as follows:

1. Place the log plain onto the work table (9).

2. Your machine is equipped with Two-hands Con-

trol System that requires to be operated by both

hands of the user – left hand controls the control

lever (12) while right hand controls the push but-

ton switch (6).

3. Simultaneously push button switch (6) to start the

splitting action.

The log splitter will freeze upon absence of either

hand.

Never force your machine for more than 5 seconds by

keeping pressure on it to split excessively hard wood.

After this time interval, the oil under pressure will be

overheated and the machine could be damaged. For

such extremely hard log, rotate it by 90° to see wheth-

er it can be split in a different direction. In any case,

if you are not able to split the log, this means that its

hardness exceeds the capacity of the machine and

thus should be discarded to protect the log splitter.

10.4 Hoist limiting

It is reasonable to limit the hoist of the pressure plate

(10) for short splitting material. Thereto press the con-

trol lever (12) and the release button (6) and let the

pressure plate (10) move just in front of the splitting

material.

Release the release button now and mount the hoist

limiting ring (7a) to the housing and tighten it. After-

wards you can release the hydraulics lever.

The pressure plate will now be resting in the selected

position.

2. Ensure that the table and the protective guard are

level in relation to each other.

3. Undo the screw on the left of the foot.

4. Fasten the other end of the strut to the protective

guard using the Phillips head screw and nut, align

everything and tighten the screws rmly.

5. Now guide the open end of the strut (N) between

the screw and the foot bracket, tighten the screw

slightly.

6. Repeat the process on the other side.

7. Align both tables in relation to each other and use

the Phillips head screws and nuts (e) to afx them.

9.5 Installing the guard (E - J) (enclosed

accessories bag f) (g. 9 + 10)

1. Connect the guards (H) and (I) together, use two

Phillips head screws, clamping brackets and nuts

to afx it.

2. Fasten the guards (H, I, J) to the holes provided

for this. These are on the side of the table and

the protective guard. Fasten the guard with seven

Phillips head screws, clamping brackets and nuts.

Fit the protective guard (G) to the control lever

protection (11) and use a Phillips head screw and

a nut to afx it.

3. Now fasten the guards (E + F) on the top. Fasten

them with eight Phillips head screws, clamping

brackets and nuts.

4. Fasten the guards (E + F) together using two

Phillips head screws, clamping brackets and nuts.

m IMPORTANT!

You must fully assemble the appliance before using it

for the rst time!

10. Initial operation

Before start-up, place the splitter on a stable, level

and at workbench so that the splitter tray table sits

at a height of 72 - 85 cm. If the machine should slip

during splitting work, fasten it to the table with two

screws (M8 x X = thickness of the table). To do so,

use the two holes on the foot (16).

Make sure the machine is completely and expertly

assembled. Check before every use:

• the connection cables for any defective spots

(cracks, cuts etc.).

• the machine for any possible damage.

• the rm seat of all bolts.

• the hydraulic system for leakage.

• the oil level and

• the safety devices

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL400CH Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info