Bedienungsanleitung Scheppach HL455 (Seite 22 von 100) (Deutsch, Englisch, Französisch, Italienisch)

781964

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

10.1 Checking the oil level (17)

The hydraulic unit is a closed system with oil tank, oil

pump and control valve. Check the oil level regularly

before every use. Too low an oil level can damage the

oil pump. The correct oil level is approx. 10 to 20 mm

below the oil tank surface.

If the oil level is at the lower notch, then the oil level is

at a minimum. Should this be the case, oil must be im-

mediately added. The upper notch indicates the max-

imum oil level. The machine must be on level ground.

Screw in the oil dipstick fully, to measure the oil level.

10.2 Ventilation screw (16)

Before operating your machine, the bleed screw

should be loosened by some rotations until air can go

in and out of the oil tank smoothly. Failed to loosen the

bleed screw will keep the sealed air in hydraulic sys-

tem being compressed after being decompressed.

Such continuous compression/decompression will

blow out the seals of the hydraulic system and cause

permanent damage to your machine.

Before moving your machine, make sure the bleed

screw is tightened to avoid oil leaking from this point.

10.3 Splitting logs

Only split logs that have been sawn off straight. To do

this, proceed as follows:

1. Place the log plain onto the work table.

2. Your machine is equipped with Two-hands Con-

trol System that requires to be operated by both

hands of the user – left hand controls the control

lever (15) while right hand controls the push but-

ton switch (14).

3. Close the protective guard (3) so that the safety

switch is actuated.

4. Press the operating lever (15) downwards and in-

itiate the splitting process by pressing the release

button (14).

The log splitter will freeze upon absence of either

hand. If the protective guard (3) is opened during the

splitting process, the unit stops immediately.

Never force your machine for more than 5 seconds by

keeping pressure on it to split excessively hard wood.

After this time interval, the oil under pressure will be

overheated and the machine could be damaged. For

such extremely hard log, rotate it by 90° to see wheth-

er it can be split in a different direction. In any case,

if you are not able to split the log, this means that its

hardness exceeds the capacity of the machine and

thus should be discarded to protect the log splitter.

3. Connect the splitter to the stand (6) with 5 round

head screws with set of square and self-locking

nuts, the nuts must be installed on the outside.

9.3 Installing the protective guard (Fig. 9 - 14)

1. Attach the handle (2) and x it with two pan-head

screws with hexagon socket (M8 x 12mm) and

washers.

2. Now fasten the protective guard (1) between the

hand guard and the pressure stamp with two pan-

head screws with hexagon socket (M8 x 12mm).

Then x the protective guard to the hand guard

with a pan-head screw with hexagon socket (M8 x

16mm), a washer and a hexagon nut.

3. Now attach the protective guard (4). Place it in

the metal lugs to the left and right of the splitting

wedge. Fix the tting with four pan-head screws

with hexagon socket (M5 x 16mm), washers and

hexagon nuts.

4. Now install the last protective guard (3) Attach

the handle (2) and x it with two pan-head screws

with hexagon socket (M8 x 12mm) and washers.

Fasten the plain bearings to the lower side of the

protective guard (3) with two pan-head screws

with hexagon socket (M6 x 35mm), one washer

and one hexagon nut. Leave the screws loose for

the time being.

Make sure that the actuator of the safety

switch is installed on the correct side.

5. Now slide the protective guard (3) onto the sliding

shafts as shown in Fig. 14 and move it forward

until the actuator engages in the safety switch.

6. Now tighten all screws of the plain bearings.

9.4 Installing the tray table (5) (Fig. 15 + 16)

1. Attach the tray table to the protective panels and

secure with four pan-head screws with hexagon

socket (M6 x 16mm), washers and hexagon nuts.

m IMPORTANT!

You must fully assemble the appliance before using it

for the rst time!

10. Initial operation

Make sure the machine is completely and expertly as-

sembled. Check before every use:

• the connection cables for any defective spots

(cracks, cuts etc.).

• the machine for any possible damage.

• the rm seat of all bolts.

• the hydraulic system for leakage.

• the oil level and

• the safety devices

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL455 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info