Bedienungsanleitung Scheppach HM100MP (Seite 27 von 236) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Finnisch)

759296

Zoom out

Zoom in

Vorherige Seite

1/236

Nächste Seite

27GB

(33) and inner ange (39).

• Insert the new saw blade (7) in the reverse se-

quence and tighten.

• Position the guide bar (40) on the pin again, and se-

cure with the spring (41).

• Important! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (7)

must coincide with the direction of the arrow on the

housing.

• Before continuing your work make sure that all safe-

ty devices are in good working condition.

• Important! Every time that you change the saw

blade (7), check to see that it spins freely in the ta-

ble insert (11) in both perpendicular and 45° angle

settings.

• Important! The work to change and align the saw

blade (7) must be carried out correctly.

8.11 Using the laser (Fig. 16,17)

• To switch on: Move the ON/OFF switch of the laser

(35) to the “1” position. A laser line is projected onto

the material you wish to process, providing an exact

guide for the cut.

• To switch off: Move the ON/OFF switch of the laser

(35) to the “0” position.

• Replacing the battery: Switch off the laser (34).

Remove the battery compartment cover (37). Re-

move the batteries and replace with new batter-

ies (3 x AG13) Check that the battery terminals are

positioned correctly when inserting new batteries.

Close the battery compartment (36) again.

8.12 Changing the speed (Fig. 2)

The saw has 2 speed ranges:

langsam schnell

vitesse lente vitesse rapide

slow fast

Pomalu rychle

Pomalý rýchly

Počasnega hitrega

lassú gyors

бавно бързо

Nopea hidas

• To operate the saw at a speed of 3200 rpm (metal),

set the switch (42) to position I.

• To operate the saw at a speed of 4500 rpm (wood),

set the switch (42) to position II.

9. Transport (Fig. 1,2)

• Tighten the set screw (26) in order to lock the rotary

table (16)

• Activate the release lever (3), press the machine

head (5) downwards and secure with the safety pin

(24). The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw for

drag guide (23) in rear position.

• Carry the equipment by the xed saw table (17).

• When reassembling the equipment proceed as de-

scribed under section 7.1.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to time

using a cloth. In order to extend the service life of the

tool, oil the rotary parts once monthly. Do not oil the

motor.

When cleaning the plastic do not use corrosive prod-

ucts.

Brush inspection

Check the carbon brushes after the rst 50 operating

hours with a new machine, or when new brushes have

been tted. After carrying out the rst check, repeat the

check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the spring

or contact wire are burned or damaged, it is necessary

to replace both brushes. If the brushes are found to be

usable following removal, it is possible to reinstall them.

11. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the mo-

tor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the ap-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM100MP Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info