Bedienungsanleitung Scheppach HM120L Redstone (Seite 26 von 44) (Deutsch, Englisch, Französisch)

782500

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

26 GB

Attention! For bevel cuts (inclined saw head), the

moveable stop rail (28) must be xed in the outer

position on both sides. (see Fig. 11)

• Open the set screw (29) on the moveable stop rail

(28) and push the moveable stop rail (28) outwards.

• The moveable stop rail (28) must be locked in a posi-

tion far enough from the inner position that the dis-

tance between the stop rail (28) and the saw blade

(7) is no more than 8 mm. (see Fig. 12)

• Before making the cut, check that no collision could

occur between the stop rail (28) and the saw blade (7).

• Tighten the set screw (29) again.

• Loosen the locking handle (13) counterclockwise and

pull the indexed position lever (12) with the index n-

ger at top.

• Set the turntable (16) to the desired angle by using

the locking handle (13). The pointer (14) on the turn-

table (16) must match with the desired angular scale

(15) on the xed saw table (17).

• Turn the locking handle (13) clockwise to x the turn-

table (16).

• Cut as described under section 8.4.

8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/11-14)

The crosscut saw can be used to make mitre cuts of 0°

- 45° to left/right in relation to the work face.

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (28a/28b) must be xed at

the outer position.

• Open the locking screw (29) for the adjustable stop

rail (28) and push the adjustable stop rail (of inclined

side) outwards. (see Fig. 13+14)

• The other adjustable stop rail (28) must be xed far

enough in front of the innermost position that the dis-

tance between the stop rail (28) and the saw blade (7)

amounts to a maximum of 8 mm. (see Fig. 12)

• Before making a cut, check that the stop rail (28) and

the saw blade (7) cannot collide.

• Secure the locking screw (29) again.

• Move the machine head (5) to the top position.

• Fix the rotary table (16) in the 0° position.

• Loosen the locking lever (22) and use the handle (1)

to angle the machine head (5) to the left/right, until

the pointer (20) indicates the desired angle measure-

ment on the scale (19).

• Re-tighten the locking lever (22).

• Cut as described in section 8.4.

8.7 Mitre cut 0°- 45° and turntable 0°- 45°

(Fig. 1-2/11-14)

The crosscut saw can be used to make mitre cuts to the

left/right of 0°- 45° in relation to the work face and, at

the same time, 0°- 45° to the left or 0°- 45° to the right

in relation to the stop rail (double mitre cut).

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (28) must be xed at the

outer position.

• Open the locking screw (29) for the adjustable stop

rail (28a/28b) and push the adjustable stop rail (of in-

clined side) outwards. (see Fig. 13+14)

• The other adjustable stop rail (28) must be xed far

enough in front of the innermost position that the dis-

tance between the stop rail (28) and the saw blade (7)

amounts to a maximum of 8 mm. (see Fig. 12)

• Before making a cut, check that the stop rail (28) and

the saw blade (7) cannot collide.

• Secure the locking screw (29) again.

• Move the machine head (5) to its upper position.

• Loosen the locking handle (13) counterclockwise and

pull the indexed position lever (12) with the index n-

ger at top.

• Set the turntable (16) to the desired angle by using

the locking handle (13). The pointer (14) on the turn-

table (16) must match with the desired angular scale

(15) on the xed saw table (17).

• Turn the locking handle (13) clockwise to x the turn-

table (16).

• Loosening the locking lever (22).

• Use the handle (1) to angle the machine head (5) to

the left/right, until the pointer (20) indicates the de-

sired angle measurement on the scale (19). (in this

connection see also section 8.6).

• Re-tighten the locking lever (22).

• Cut as described under section 8.4.

8.8 Limiting the cutting depth (Fig. 3)

• The cutting depth can be innitely adjusted using the

screw (26). To do this loosen the knurled nut on the

screw (26). Move the stop for the cutting depth limi-

tre (27) to the outside. Turn the screw (26) in or out

to set the required cutting depth. Then re-tighten the

knurled nut on the screw (26).

• Check the setting by completing a test cut.

8.9 Sawdust bag (Fig. 2)

The saw is equipped with a debris bag (21) for sawdust

and chips.

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (21) can be emptied by means of a zip-

per at the bottom.

8.10 Changing the saw blade (Fig. 15-18)

Remove the power plug!

Important.

Wear safety gloves when changing the saw blade.

Risk of injury!

• Blade guard (6) open

• Loosen the screw (36)

• Blade guard (6) upwards until it is held

• Firmly press the saw shaft lock (4), and slowly turn

the ange screw (32) clockwise. After max. one turn,

the saw shaft lock (4) engages.

• Then undo the ange screw (32), by applying a slight-

ly greater force in a clockwise direction.

• Fully unscrew the ange screw (32) and remove the

outer ange (33).

• Then remove the saw blade (7) from the inner ange

(39) and pull out in a downwards direction.

• Carefully clean the ange screw (32), outer ange

(33) and inner ange (39).

Scheppach HM120L Redstone Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info