Bedienungsanleitung Scheppach HM140L (Seite 27 von 212) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch, Schwedisch, Finnisch)

781431

Zoom out

Zoom in

Vorherige Seite

1/212

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

| 27

b) Use clamps to support the workpiece when-

ever possible. If supporting the workpiece

by hand, you must always keep your hand

at least 100 mm from either side of the saw

blade. Do not use this saw to cut pieces that

are too small to be securely clamped or held

by hand. 





c) The workpiece must be stationary and

clamped or held against both the fence and

the table. Do not feed the workpiece into the

blade or cut “freehand” in any way. -





d) Push the saw through the workpiece. Do not

pull the saw through the workpiece. To make

a cut, raise the saw head and pull it out over

the workpiece without cutting, start the mo-

tor, press the saw head down and push the

saw through the workpiece. 







e) Never cross your hand over the intended line

of cutting either in front or behind the saw

blade. 



-



f) Do not reach behind the fence with either

hand closer than 100 mm from either side of

the saw blade, to remove wood scraps, or for

any other reason while the blade is spinning.



  -



g) Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence. Al-

ways make certain that there is no gap be-

tween the workpiece, fence and table along

the line of the cut. 







h) Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the work-

piece.        





i) Cut only one workpiece at a time. -

     

-



j) Ensure the mitre saw is mounted or placed on

a level, rm work surface before use. 





k) Plan your work. Every time you change the

bevel or mitre angle setting, make sure the ad-

justable fence is set correctly to support the

workpiece and will not interfere with the blade

or the guarding system. 









l) Provide adequate support such as table ex-

tensions, saw horses, etc. for a workpiece

that is wider or longer than the table top.

-

󰀨





m) Do not use another person as a substitute for

a table extension or as additional support. -

       







n) The cut-o󰀨 piece must not be jammed or

pressed by any means against the spinning

saw blade. 

󰀨



o) Always use a clamp or a xture designed to

properly support round material such as rods

or tubing. -

         



p) Let the blade reach full speed before contact-

ing the workpiece. 



q) If the workpiece or blade becomes jammed,

turn the mitre saw o󰀨. Wait for all moving

parts to stop and disconnect the plug from

the power source and/or remove the battery

pack. Then work to free the jammed material.





r) After nishing the cut, release the switch,

hold the saw head down and wait for the blade

to stop before removing the cut-o󰀨 piece.





s) Hold the handle rmly when making an incom-

plete cut or when releasing the switch before

the saw head is completely in the down posi-

tion.        

       



Scheppach HM140L Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info