Bedienungsanleitung Scheppach HS100S (Seite 11 von 86) (Deutsch, Englisch, Polnisch)

781486

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

11 І 86

–Do not use saw blades made of high-speed alloy

steel (HSS steel).

–In times of non-use keep the push stick or the

push block with the electrical power tool in its

holder at all times.

2 Maintenance and repair

–Pull out the mains plug for any adjustment or

repair tasks.

–The generation of noise is inuenced by various

factors, including the characteristics of saw

blades, condition of saw blade and electric

tool. Use saw blades which were designed for

reduced noise development, insofar as possible.

Maintain the electric tool and tool attachments

regularly and if necessary, initiate repairs in

order to reduce noise.

–Report faults on the electric tool, protective

devices or the tool attachment to the person

responsible for safety as soon as they are dis-

covered.

3 Safe work

–Use the push stick or handle with sliding wood,

to pass the workpiece securely out off the saw

blade.

–Make sure that the riving knife is always used,

and set up is correctly.

–Use the upper blade guard and set it to the cor-

rect position.

–Only use saw blades for which the maximum

permissible speed is not lower than the maxi-

mum spindle speed of table saws and which are

suitable for the material to be cut.

–Do not cut rebates or grooves without tting a

suitable guard, e.g. a tunnel-type guard, over the

saw table.

–Circular saws must not be used for slotting jobs

(cutting grooves which end in the workpiece).

–When transporting the electric tool, only use

the transport devices. Never use the protective

devices for handling or transport.

–Make sure that the upper part of the saw blade

is covered during transport, e.g. by the protective

device.

–Be sure to only use spacers and spindle rings

specied by the manufacturer as suitable for the

intended purpose.

–The oor around the machine must be level,

clean and free of loose particles, such as chips

and cutting residues.

–Always stand to the side of the saw blade when

working with the saw.

–Do not remove any cutting residues or other

parts of workpieces from the cutting zone while

the machine is running and the saw unit is not

at rest.

–Make sure that the machine is always secured

on a workbench or a table if at all possible.

–Support long workpieces (e.g. with a roller table)

to prevent them sagging at the end of a cut.

–m Attention! Never remove loose splinters, chips

or jammed pieces of wood while the saw blade is

running.

• Switch off the machine to troubleshoot or remo-

ve jammed pieces of wood. - Disconnect the

main power plug -

• Retting, including adjusting and measuring

works, and cleaning must be carried out only

when the motor is switched off. - Disconnect

the main power plug -

• Before switching on again, ensure that keys

and adjustment tools have been removed.

19 Check the electric tool for potential damage

–Protective devices and other parts must be care-

fully inspected to ensure that they are fault-free

and function as intended prior to continued use

of the electric tool.

–Check whether the moving parts function fault-

lessly and do not jam or whether parts are dam-

aged. All parts must be correctly mounted and all

conditions must be fullled to ensure fault-free

operation of the electric tool.

–The moving protective hood may not be xed in

the open position.

–Damaged protective devices and parts must be

properly repaired or replaced by a recognised

workshop, insofar as nothing different is speci-

ed in the operating manual.

–Damaged switches must be replaced at a cus-

tomer service workshop.

–Do not use any faulty or damaged connection

cables.

–Do not use any electric tool on which the switch

cannot be switched on and off.

20 ATTENTION!

–Exercise elevated caution for double mitre cuts.

21 ATTENTION!

–The use of other insertion tools and other acces-

sories can entail a risk of injury.

22 Have your electric tool repaired by a qualied

electrician

–This electric tool conforms to the applicable safety

regulations. Repairs may only be performed by an

electrician using original spare parts. Otherwise

accidents can occur.

23 Do not use the cable for purposes for which it

is not intended

–Do not use the cable to pull the plug out of the

outlet. Protect the cable from heat, oil and sharp

edges.

ADDITIONAL SAFETY INSTRUCTIONS

1 Safety precautions

–Warning! Do not use damaged, cracked or

deformed saw blades.

–Replace a worn table insert.

–Only use saw blades recommended by the

manufacturer which conform to EN 847-1.

m Warning! Keep attention When changing the

saw blade.The cutting width is not smaller and

the main blade thickness of the saw blade is not

greater than the thickness of the gap wedge!

–Make sure that a suitable saw blade for the ma-

terial to be cut is selected.

–Wear suitable personal protective equipment.

This includes:

Hearing protection to avoid the risk of becoming

hearing impaired,

Respiratory protection to avoid the risk of inhal-

ing harmful dust,

–Wear gloves when handling saw blades and

rough materials.

–Carry saw blades in a container whenever practi-

cal.

–Wear goggles. Sparks generated during work or

splinters, chippings and dust coming from the

device can lead to loss of eyesight.

–Connect a dust collecting device to the electric

tool when sawing wood. The emission of dust

is inuenced, among other things, by the type

of material to be processed, the signicance of

local separation (collection or source) and the

correct setting of the hood/guide plates/guides.

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

Scheppach HS100S Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info