Bedienungsanleitung Scheppach HS100S (Seite 14 von 86) (Deutsch, Englisch, Polnisch)

781486

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

14 І 86

10. Operation

Working instructions

After each new adjustment it is advisable to carry out a

trial cut in order to check the set dimensions. After switch-

ing on the saw, wait for the blade to reach its maximum

speed of rotation before commencing with the cut.

Secure long workpieces against falling off at the end of

the cut (e.g. with a roller stand etc.)

Take extra care when starting the cut!

Never use the equipment without the suction function.

Regularly check and clean the suction channels.

Suitability of the saw blades:

- 24 teeth: soft materials, large chip depth, coarse cut

prole

- 48 teeth: hard materials, small chip depth, ne cut

prole

10.1 Making longitudinal cuts (Figure 19)

Longitudinal cutting (also known as slitting) is when you

use the saw to cut along the grain of the wood.

Press one edge of the workpiece against the parallel stop

(15) while the at side lies on the saw table (1). The blade

guard (4) must always be lowered over the workpiece.

When you make a longitudinal cut, never adopt a work-

ing position that is in line with the cutting direction.

- Set the parallel stop (15) in accordance with the work-

piece height and the desired width. (See 9.4)

- Switch on the saw.

- Place your hands (with ngers closed) at on the

workpiece and push the workpiece along the parallel

stop (15) and into the blade (3).

- Guide at the side with your left or right hand (depend-

ing on the position of the parallel stop) only as far as

the front edge of the saw blade guard (4).

- Always push the workpiece through to the end of the

splitter (6).

- The offcut piece remains on the saw table (1) until the

blade (3) is back in its position of rest.

- Secure long workpieces against falling off at the end

of the cut (e.g. with a roller stand etc.) (e.g. roller table

etc.)

10.1.1 Cutting narrow workpieces (Fig. 20)

Be sure to use a push stick (9) when making longitudinal

cuts in workpieces smaller than 120 mm in width. A push

block is supplied with the saw! Replace a worn or dam-

aged push stick immediately.

• Adjust the parallel stop to the width of workpiece you

require. (see 9.4)

• Feed in the workpiece with two hands. Always use the

push stick (9) in the area of the saw blade.

• Always push the workpiece through to the end of the

splitter.

m Caution! With short workpieces, use the push stick

from the beginning.

10.1.2 Making angular cuts (Fig. 21)

Angular cuts must always be made using the parallel

stop (15).

- Set the blade to the desired angle. (See 9.3)

- Set the parallel stop (15) in accordance with the work-

piece width and height (see 9.4)

- Carry out the cut in accordance with the workpiece

width (see 10.1).

9.3 Setting the angle (Fig. 14)

With the table saw you can make diagonal cuts to the

left oriented to the stop bar from 0 ° to 45 °.

m Check before each cut, that between the stop bar

(e), cross-stop (13) and the saw blade (5) a collision is

not possible.

- Undo the xing handle (13).

- Set the desired angle on the scale by pressing and

turning the hand wheel (12).

- Lock the xing handle (13) again in the required angle

position.

9.4 Working with the rip fence

9.4.1 Setting the stop height (gs. 15-16)

- The stop rail (27) of the rip fence (15) has two guide

surfaces with different heights.

- Depending on the thickness of the material to be cut,

the stop rail (27) as shown in g. 16 must be used for

thick material (about 25 mm workpiece thickness) and

that shown in g. 15 for thin material (less than 25 mm

workpiece thickness).

9.4.2 Turning the stop rail (gs. 15-16)

- Loosen the wing nuts (28) rst for rotating the stop rail

(27).

- Now, the stop rail (27) can be removed from the guide

rail (29) and pushed over it again using the correspon-

ding guide.

- Tighten the wing nuts (28) again.

- The stop rail (27) can be applied to the left or right of

the guide rail (29) as needed. To this end, only install

the bolts from the other side of the guide rail (29).

9.4.3 Setting the cutting width (g. 17)

- The rip fence (15) must be used for longitudinal cut-

ting of wood parts.

- The rip fence (15) should be mounted on the right

side of the saw blade (3).

- Set the rip fence (15) on top of the guide rail for rip

fence (14).

- On the guide rail for rip fence (14), there are 2 scales

which indicate the distance between the rip fence (15)

and the saw blade (3).

- Select the appropriate scale depending on whether

the stop rail (27) is rotated for processing thick or thin

material:

High stop rail (thick material):

Low stop rail (thin material):

- Set the rip fence (15) to the desired level in the sight

glass and x it with the eccentric lever for the rip fence

(30).

9.5 Transverse stop (g. 18)

- Push the transverse stop (13) into a groove (31) of the

saw bench.

- Loosen the handle screw (32).

- Turn the cross stop (7) until the desired angle is set.

The arrow on the transverse stop is at the set angle.

- Tighten the knurled screw (32) again.

- The stop bar (34) can be moved on the transverse

stop (13). Loosen the nuts (33) and push the stop

rail (34) to the desired position. Tighten the nuts (34)

again.

Caution!

- Do not push the stop rail (34) too far towards the saw

blade.

- The distance between the stop rail (34) and saw blade

(3) should be about 2 cm.

Scheppach HS100S Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info