Bedienungsanleitung Scheppach HS116 (Seite 38 von 72) (Deutsch, Englisch, Französisch)

782563

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

38 | GB

To change the angle of the transverse stop (19), pro-

ceed as follows:

1. Loosen the clamping handle (19c) by turning it

counterclockwise.

2. Turn the transverse stop (19) until the arrow points

to the desired angle.

3. Secure this position by turning the clamping han-

dle (19c) clockwise.

9.8 Connecting an extraction device (g. 24 + 25)

m WARNING

Danger of injury for eyes due to swirling chips

- Wear eye protection.

- Only operate the product with a suitable chip

extraction system. Do not use a common house-

hold vacuum cleaner.

1. Screw the hose clamp for the extraction hose (23)

into the right table width extension (9) using a

Phillips screw M5 x 10mm (F), two small washers

(H) and a nut M5 (M). (g. 24)

2. Place the extraction hose (6) on the extraction

port (22) at the rear of the machine, push the ex-

traction hose (23) through the hose clamp and

attach it to the extraction port of the saw blade

guard (2). (g. 25)

3. Connect a suitable chip extraction system (not in-

cluded in the scope of delivery) to the extraction

port (22).

ATTENTION

Check and clean the extraction channels at regular

intervals.

10. Before commissioning

10.1 General notes

• Check that the product is fully assembled.

• Check that the safety covers are present, installed

and functional.

• Check that the switches work as intended.

• Check that the product is on a rm footing.

• Check that the labels on the product are present and

legible. Missing or damaged labels must be replaced

or exchanged.

• Check that the mains voltage and the operating volt-

age match, see Technical data.

• Check that the supply lines, extensions, cable

drum, etc. are not too long. Otherwise there may

be a drop in voltage or delay in motor start-up.

• Check that the ambient temperature is observed.

10.2 Product-specic notes

• The machine must be securely installed.

• It must be possible for the saw blade to run freely.

• In case of previously machined wood, be aware of

any foreign bodies, such as nails or screws, etc.

9.5 Fitting the saw blade guard (g. 19)

1. Place the saw blade guard (2) onto the riving knife

(3) from above.so that the xing screw (2a) ts

through the hole in the riving knife.

2. Tighten the xing screw (2a).

Attention! The saw blade guard (2) must remain

free to move.

3. Ensure that the saw blade guard (2) can move

freely.

4. Disassembly takes place in reverse order.

m WARNING

Danger of injury due to incorrect tted saw blade

guard

- Before starting sawing, ensure that the saw

blade guard (2) automatically lowers onto the

material to be sawn.

9.5.1 Checking the saw blade guard

After tting, check that the saw blade guard (2) is

functioning properly.

1. Lift the saw blade guard (2) and then release it.

2. The saw blade guard (2) should automatically

move back to its starting position.

9.6 Fitting the parallel stop (g. 20)

1. First place the parallel stop (8) with open eccen-

tric lever (8b) on the rear guide rail (7a), then on

the front guide rail (7b) on the saw table (5).

2. To change the position of the parallel stop (1),

slide the parallel stop (1) with open eccentric lever

(8b) along the front and rear guide rail (7a/7b).

3. To secure the parallel stop (1) in the desired po-

sition, press the eccentric lever (8b) fully down-

wards.

9.6.1 Attaching the stop rail to the parallel stop

(g. 21 + 22)

1. Insert the two coach bolts M6 x 55 mm (E)

from the inside into the parallel stop (8) and

secure them with the two knurled nuts (G).

Attention! Do not tighten the knurled nuts (G) yet.

(g. 21)

2. Push the stop rail (8a) through the two coach

bolts (E) into the desired position and tighten the

knurled nuts (G). (g. 22)

9.7 Fitting the transverse stop (g. 23)

1. Push the transverse stop (19) into the groove (28)

of the sliding carrier plate (21).

2. Now place the guide rail (19b) including the

screws into the marked grooves of the transverse

stop (19) (g. 23).

3. Move the guide rail (19b) into the desired position

and tighten the knurled nut (19d).

4. Screw the clamping handle (19c) into the trans-

verse stop (19) by turning it clockwise.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HS116 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info