Bedienungsanleitung Scheppach HS520 (Seite 26 von 52) (Deutsch, Englisch, Französisch)

781860

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

26 GB

• Do not allow other persons, especially children, to

touch the tool. Keep them out of your work area.

• Persons working on the machine should not be

distracted.

• Note the direction of rotation of the motor and saw

blade. Use only blades whose permissible maxi-

mum speed is not lower than the maximum spindle

speed of the circular saw and of the material to

be cut.

• After you have switched off the motor, never slow

down the saw blade by applying pressure to its

side.

• Only t blades which are well sharpened and have

no cracks or deformations.

• Do not use circular saw blades made of high-speed

alloy steel (HSS steel)

• Only use saw blades that are recommended by the

manufacturer, comply with EN 847-1.

• Faulty saw blades must be replaced immediately.

• Never use saw blades which do not comply with

the data specied in this manual.

• Never dismantle the machines safety devices or

render them inoperative.

• If the table insert is worn, replace it.

• Always stand to the side of the saw blade when

working with the saw.

• Never load the machine so much that it cuts out.

• Make sure that off-cuts do not catch on the saw

blade crown.

• Never remove loose splinters, chips or jammed

pieces of wood when the saw blade is running.

• To rectify faults or remove jammed pieces of wood,

always switch off the machine rst. - Unplug the

power plug -

• If the sawing gap is worn, replace the table insert.

Switch off the machine and pull out the mains plug.

• Carry out retooling work, adjustments, measure-

ments and cleaning jobs only when the motor is

switched off.

- Unplug the power plug -

• Before switching on, make sure that all keys and

wrenches have been removed from the tool.

• Switch off the motor and unplug the power plug

before you leave the workplace

• Ret all guards and safety devices immediately

after you have completed any repairs or mainte-

nance work.

• Be sure to observe the safety information and op-

erating and maintenance instructions issued by the

manufacturer, as well as the dimensions listed in

the Technical Data.

• It is imperative to observe the accident prevention

regulations in force in your area as well as all other

generally recognized rules of safety.

• Make sure you stand squarely and keep your bal-

ance at all times.

• Each time before re-using the tool, carefully check

that the guards or any slightly damaged parts are

working as intended.

• Check the tool for damage!

• Protective devices or other parts with minor dam-

age must be carefully inspected to ensure that they

function correctly and as intended prior to contin-

ued use of the tool.

• Check that the moving parts are in good working

order, that they do not jam, and that no parts are

damaged. Make sure that all parts are tted cor-

rectly and that all other operating conditions are

properly fullled.

• Unless otherwise stated in the operating instruc-

tions, damaged safety devices and parts must

be repaired or replaced by an authorized service

center.

• This tool conforms to the applicable safety regula-

tions. Repairs may only be performed by a special-

ist using original spare parts. Otherwise accidents

could occur.

• If necessary, wear suitable personal protection

equipment. This could consist of:

- Ear plugs to prevent the risk of damaging your

hearing;

- A breathing mask to avoid the risk of inhaling

hazardous dust.

- Eye protection to prevent foreign bodies entering

the eyes.

- Safety shoes for stability and protection against

falling objects.

- Always wear gloves when handling saw blades

and rough materials. Whenever practicable, saw

blades must be carried in a container.

- Safety goggles / face protection to avoid injuries

due ying objects.

- Protective clothing to prevent cutting injuries.

• The operator must be informed about the condi-

tions that inuence the generation of noise (for

example saw blades designed to reduce noise

emissions, caring for blades and the machine).

• Faults on the machine or its guards, safety devices

and blade must be reported to the person in charge

as soon as they are discovered.

• Use only the transport devices to move the ma-

chine. Never use the guards for handling and mov-

ing the machine.

• All operators must receive proper training in the

use, adjustment and operation of the machine.

• Do not saw any materials that contain foreign bod-

ies such as wires, cables or ties.

• Only use sharp saw blades.

Warning! This electric tool generates an electro-

magnetic eld during operation. This eld can im-

pair active or passive medical implants under certain

conditions. In order to prevent the risk of serious

or deadly injuries, we recommend that persons with

medical implants consult with their physician and the

manufacturer of the medical implant prior to operating

the electric tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HS520 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info