Bedienungsanleitung Scheppach HWW1300 (Seite 26 von 88) (Deutsch, Englisch, Französisch, Finnisch)

781427

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

26 | GB

Damaged electrical connection cable

The insulation on electrical connection

cables is often damaged. This may have

the following causes:

• Passage points, where connection cables

are passed through windows or doors.

• Kinks where the connection cable has

been improperly fastened or routed.

• Places where the connection cables

have been cut due to being driven over.

• Insulation damage due to being ripped

out of the wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection ca-

bles must not be used and are life-threat-

ening due to the insulation damage.

Check the electrical connection cables

for damage regularly. Make sure that the

connection cable does not hang on the

power network during the inspection.

Electrical connection cables must comply

with the applicable VDE and DIN provi-

sions. Only use connection cables with

the marking „H05RN-F“.

The printing of the type designation on

the connection cable is mandatory. For

single-phase AC motors, we recommend

a fuse rating of 16A (C) or 16A (K) for ma-

chines with a high starting current (start-

ing from 3000 watts)!

AC motor 230 V~/ 50 Hz

Mains voltage 230 V~ / 50 Hz.

The mains connection and the extension

cable have to be three-core cables = P

+ N + SL. - (1/N/PE). Extension cables

up tp 25m long must have a minimum

cross-section of 1.5 mm². Mains fuse pro-

tection is 16 A maximum.

9. Initial operation

m IMPORTANT!

You must fully assemble the appliance

before using it for the rst time!

• Install the equipment on a solid and lev-

el surface.

• Unscrew the coarse lter screw (8) and

remove the coarse lter (9) as shown

in Figure 3. Now you can ll the pump

housing with water via the coarse lter

screw (8). Filling the intake line acceler-

ates the in take process.

• Assemble in reverse order.

• Open the discharge line.

• Connect the mains cable.

• Switch on the equipment with the power

switch (12) water can be suctioned in for

up to 5 minutes (max mum suction height).

• After pressure drop due to water con-

sumption switches the unit automatically

on (switch-on pressure approx. 1.5 bar)

• The domestic waterworks can be used

for domestic water supply in the inner

area also be permanently installed. To

avoid vibrations and noise should be

minimised. the pump with exible hose

lines connected to the pipe network will

be. Anti-vibration material is also rec-

ommended, z. e.g. a rubber layer, be-

tween pump and base to lay. Ensure a

stable Fixing of the container by means

of Screws that pass through the holes

t in the stand.

Electrical connection

The electrical motor installed is connect-

ed and ready for operation. The connec-

tion complies with the applicable VDE

and DIN provisions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HWW1300 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info