Bedienungsanleitung Scheppach Lion 12.0 rh (Seite 10 von 20) (Deutsch, Englisch, Französisch)

782594

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

maximum no-load speed is reached only in

the operating modes drilling and hammer

drilling.

• Replace a damaged dust protection cap

immediately. The dust protection cap largely

prevents the penetration of drilling dust

into the tool holder during operation. When

inserting the tool, pay attention that the dust

protection cap is not damaged.

• Dusts from materials such as lead-contai-

ning coatings, some wood types, minerals

and metal can be harmful to one’s health

and cause allergic reactions, lead to respi-

ratory infections and/or cancer. Materials

containing asbestos may only be worked by

specialists.

- As far as possible, use a dust extraction

system suitable for the material.

- Provide for good ventilation of the working

place.

- It is recommended to wear a P2 lter-class

respirator. Observe the relevant regulations

in your country for the materials to be wor-

ked.

• Prevent dust accumulation at the workplace.

Dusts can easily ignite.

• If the application tool should become

blocked, switch the machine off. Loosen the

application tool.

• When switching on with a blocked drilling

tool, high torque reaction can occur.

• Apply the power tool to the screw only when

it is switched off. Rotating tool inserts can

slip off.

• Always wait until the machine has come

to a complete stop before placing it down.

The tool insert can jam and lead to loss of

control over the power tool.

• To save energy, only switch the power tool

on when using it.

• Avoid unintentional switching on. Ensure

the On/Off switch is in the off position before

inserting battery pack. Carrying the power

tool with your nger on the On/Off switch or

inserting the battery pack into power tools

that have the switch on invites accidents.

• Do not open the battery. Danger of short-

circuiting.

• In case of damage and improper use of the

battery, vapours may be emitted. Ventilate

the area and seek medical help in case of

complaints. The vapours can irritate the

respiratory system.

• Use the battery only in conjunction with your

power tool. This measure alone protects the

battery against dangerous overload.

• Use only original batteries with the voltage

listed on the nameplate of your power tool.

When using other batteries, e.g. imitations,

reconditioned batteries or other brands,

there is danger of injury as well as property

damage through exploding batteries.

• The battery is supplied partially charged. To

ensure full capacity of the battery, complete-

ly charge the battery in the battery charger

before using your power tool for the rst

time.

• Read the operating instructions of the batte-

ry charger.

• Check the tight seating of the battery. Two

locking levels are possible.

Intended Use m

The power tool is intended for hammer drilling

in concrete, brick and stone. It is also suitable

for drilling without impact in wood and metal,

as well as for screwdriving.

Remaining risks m

Even if you use this electric power tool

in accordance with instructions, certain

residual risks cannot be rules out. The

following hazards may arise in connection

with the equipment´s construction and

layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm

vibrations if the equipment is used over a

prolonged period

Equipment Fig.1

1. Tool holder SDS-Plus

2. Debit note

3. Display forward / reverse operation

4. Direction of rotation switch

5. On / off switch

6. Accumulator

7. Snap button

8. Dust cap

9. Switch for operating mode setting

10. Working mode percussive drilling

11. Working mode drilling

Startup

Assembly of the tool

• Pull back the dust cap (Fig.1.Pos.8).

• Insert your SDS-Plus tool.

• Snap the dust cap (Fig.1.Pos.8) again.

• Dismantling: Pull back the dust cap

(Fig.1.Pos.8) and pull the SDS-Plus tool out.

Forward/Reverse switch

(Fig.1.Pos.4)

With the slide switch above the On/Off switch

you can select the direction of rotation of the

batterypowered drill/screwdriver and secure

it against being switched on accidentally. You

can choose between clockwise and anticlock-

wise rotation. To avoid causing damage to the

gearing it is advisable to change the direction

of rotation only when the tool is at a standstill.

The On/Off switch is blocked when the slide

switch is in centre position.

On/Off switch (Fig.1.Pos.5)

Innitely variable speed control is possible

with the On/Off switch. The further you press

the switch, the higher the speed of the battery-

powered drill/screwdriver.

Working with the hammer drill

• Select an appropriate SDS-Plus use tool.

(Maximum drill diameter 10 mm)

• Select the appropriate operating mode

from (Fig.1.Pos.10 + 11).

- Drilling: drilling in wood, screw driving

- Impact drilling: drilling in stoneware and

concrete

• Pay attention to the correct direction

of rotation. The direction of rotation

is displayed on the reverse indicator

(Fig.1.Pos.4).

• Start work.

• If the load indicator (Fig.1.Pos.2) is red,

the load on the engine is too high. Redu-

ce the pressure you exert on the machi-

ne. Always make sure that the indicator

light is green.

Scheppach Lion 12.0 rh Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info