Bedienungsanleitung Scheppach LS40P Woodster (Seite 19 von 32) (Deutsch, Englisch, Französisch)

782006

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

19GB

Maintenance

• A worn out or damaged cutting unit should be re-

placed by an authorised expert.

• Take care that all fastening elements (screws, nuts,

etc.) are rmly tightened, so that you can work safely

with the scarier.

• Store the scarier in a dry place.

• For longer life, all screw-fastened parts, such as

wheels and axles should be cleaned and subse-

quently oiled.

• Regular servicing of the scarier not only secures

longer endurance and performance, but also contrib-

utes to an accurate and simple scarication of your

lawn.

• At the end of the season, carry out a general check of

the scarier, and remove all residue collected. Before

the start of every season, it is absolutely necessary to

check the state of the scarier. Contact our Customer

Service if repair work is necessary.

Servicing the air lter

Soiled air lters reduce the engine output by supply too

little air to the carburetor.

Regular checks are therefore essential. The air lter

should be checked after every 50 hours of use and

cleaned if necessary. If the air contains a lot of dust,

the air lter should be checked more frequently.

• Remove the air lter as shown in Fig. 15+16.

• Clean the air lter only with compressed air or by tap-

ping it.

• Assemble in reverse order

Important: Never clean the air lter with petrol or inam-

mable solvents.

Servicing/Replacing the spark plug

Check the spark plug for dirt and grime after 10 hours

of operation and if necessary clean it with a copper wire

brush. Thereafter service the spark plug after every 50

hours of operation.

• Pull off the spark plug boot (Fig. 17) with a twist.

• Remove the spark plug using a spark plug wrench

(Fig. 18).

• Assemble in reverse order

Preparing the equipment for storage

Caution: Do not empty the petrol tank in enclosed

areas, near re or wen smoking. Petrol fumes

can cause explosions and re.

1. Empty the petrol tank with a petrol suction pump.

2. Start the engine and let it run until any remaining

petrol has been used up.

3. Change the oil at the end of every season. To do

so, remove the used engine oil from a warm engine

and rell with fresh oil.

4. Remove the spark plug from the cylinder head. Fill

the cylinder with approx. 20 ml of oil from an oil

can. Slowly pull back the starter handle, which will

bathe the cylinder wall with oil. Screw the spark

plug back in.

handles) is maintained between the user and the hous-

ing. Be especially careful when scarifying and changing

direction on slopes and inclines. Maintain a solid footing

and wear sturdy, nonslip footwear and long trousers. Al-

ways scarify along the incline (not up and down).

For safety reasons, the scarier may not be used to

scarify inclines whose gradient exceeds 15 degrees.

Use special caution when backing up and pulling the

scarier (tripping hazard)!

Tips for proper working

It is recommended that you overlap scarifying paths a

little. Try to scarify in straight lines for a nice, clean look.

In so doing, the aeration swaths should always overlap

each other by a few centimetres in order to avoid bare

strips.

As soon as grass clippings start to trail the scarier, it is

time to empty the grass basket.

Important! Before taking off the grass basket, switch off

the motor and wait until the roller has come to a stop.

To remove the grass basket, lift up the ejector ap with

one hand, while unhooking the basket with the other.

How frequently you should scarify your lawn is deter-

mined primarily by the speed at which the grass grows

and the hardness of the soil. Keep the underside of the

equipment clean and remove soil and grass build-up.

Deposits make it more dif cult to start the aerator and

decrease the quality of the scarifying. Always scarify

along inclines (not up and down). Switch off the motor

before doing any checks on the roller.

Important!

The roller rotates for a few seconds after the motor is

switched off . Never attempt to stop the roller. In the

event that the rotating roller strikes an object, immedi-

ately switch off the equipment and wait for the roller to

come to a complete stop. Then inspect the condition of

the roller. Replace any parts that are damaged.

Cleaning and maintenance

Danger!

Always pull out the mains power plug before starting

any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor hous-

ing free of dirt and dust as far as possible. Wipe the

equipment with a clean cloth or blow it with com-

pressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents or

solvents; these could attack the plastic parts of the

equipment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach LS40P Woodster Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info