Bedienungsanleitung Scheppach MS196-51 (Seite 29 von 60) (Deutsch, Englisch, Französisch, Polnisch)

781694

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

29 | GB

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

In addition, we are also not liable for any damages

arising from improper repairs. Such work should be

performed by a customer services workshop or au-

thorized specialist. The same applies to accessory

parts.

Times of use

Please comply with statutory regulations, which may

vary from location to location.

Important hint in case of sending the equipment

to a service station:

Due to security reasons please see to it that the

equipment is sent back free of oil and gas!

Ordering replacement parts

Please quote the following data when ordering re-

placement parts:

• Type of machine

• Article number of the machine

Spare parts/accessories

Lawn mower blade - Article no.: 7911200604

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the

following parts are therefore also required for use as

consumables. Wear parts*: spark plug, air lter, pet-

rol lter, knife, belt

* Not necessarily included in the scope of delivery!

10. Storage

• Never store the mower (with petrol in the tank) in-

side a building in which petrol fumes could come

into contact with open ames or sparks.

• Allow the motor to cool before you put the lawn

mower in an enclosed area.

• In order to avoid re hazards, keep the engine, ex-

haust and the area around the fuel tank free from

grass, leaves and leaking grease (oil).

Preparing the mower for long-term storage

Caution: Do not empty the petrol tank in enclosed

areas, near re or when smoking. Petrol fumes can

cause explosions and re.

• Empty the petrol tank with a petrol suction pump.

• Start the engine and let it run until any remaining

petrol has been used up.

• Change the oil at the end of every season. To do

so, remove the used engine oil from a warm engine

and rell with fresh oil.

• Remove the spark plug from the cylinder head. Fill

the cylinder with approx. 20 ml of oil from an oil

can. Slowly pull back the starter handle, which will

bathe the cylinder wall with oil. Screw the spark

plug back in.

• Clean the cooling ns of the cylinder and the hous-

ing.

Cleaning the belts (Fig. 17, 19)

• Remove the knife and the gear housing by loosen-

ing the screws out.

• Clean the elements of the transmission and the belt

once or twice a year with brush or compressed air.

• Screw the transmission housing and the knife on

again.

Care and adjustment of the cables

Oil the cables at regular intervals and check that they

move easily.

Maintenance of the air lter (Fig. 20)

A soiled air lter will reduce the performance of the

engine because it will prevent enough air getting to

the carburetor. It is therefore imperative that regular

checks are made. The air lter should be checked

every 25 hours and cleaned if required. If the air is

very dusty the air lter should be checked more regu-

larly.

Unclip the air lter cover and remove the sponge lter

element. To avoid objects falling into the air intake,

replace the air lter cover. (Fig. 20).

Important: Never clean the air lter with petrol or in-

ammable cleaning agents. Clean the air lter with

compressed air or simply by knocking out any soiling.

Maintenance of the spark plug (Fig. 21)

Check the spark plug for dirt and grime after 10 hours

of operation and if necessary clean it with a copper

wire brush. Thereafter service the spark plug after

every 50 hours of operation.

Pull off the spark plug boot with a twist. Remove the

spark plug (10) with a spark plug wrench.

Using a feeler gauge, set the gap to 0.75 mm ( 0.030”).

Ret the spark plug taking care not to overtighten.

Engine brake lever (Fig. 1)

The engine is equipped with a mechanical brake (3)

which has to be checked regularly. When releasing

the brake lever, the blade must come to a halt within

7 seconds. If this is not the case, the machine must

not be used. Contact an authorised specialist retailer.

Ensure that the machine is in a awless condition for

its entire service life. Improper maintenance may lead

to life-threatening injuries.

Repairs

After any repair or maintenance work, check that all

safety-related parts are in place and in proper work-

ing order. All parts which may cause injury must be

kept where they are inaccessible to children or oth-

ers.

Important: In accordance with product liability legis-

lation we are not liable for any damages caused by

improper repairs or the use of spare parts that are not

original spare parts or parts approved by us.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MS196-51 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info