Bedienungsanleitung Scheppach OSM100 (Seite 12 von 56) (Deutsch, Englisch, Französisch, Italienisch)

781480

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

12 english

m Proper Use

The machine meets the currently valid EU machine directive.

• The manufacturer’s safety, operation and maintenance

instructions as well as the technical data given in the

calibrations and dimensions must be adhered to.

• Relevant accident prevention regulations and other gen-

erally recognized safety and technical rules must also

be adhered to.

• The machine may only be used, maintained or repaired

by trained persons who are familiar with the machine

and have been informed about the dangers. Unauthor-

ized modiﬁcations of the machine exclude a liability

of the manufacturer for damages resulting from the

modiﬁcations.

• The machine is intended for use only with original spare

parts and original tools from the producer.

• Any other use is considered to be not intended. The

manufacturer excludes any liability for resulting dam-

ages, the risk is exclusively borne by the user.

m Remaining hazards

The machine has been built using modern technology and

in accordance with recognized safety rules.

Some hazards, however, may still remain.

• There is the danger of injuries to ﬁngers and hands by

the rotating grinding tool when there is improper guid-

ance or application of the work piece to be grinded.

• There is a danger of injuries by catapulted work pieces

when guided or ﬁxed improperly.

• The use of incorrect or damaged mains cables can lead

to electrical injuries.

• Although having regarded all considerable rules there

may still remain not obvious remaining hazrds.

• Minimize remaining hazards by following the instruc-

tions in ”Safety Rules”, ”Use only as authorized” and

in the entire operating manual.

Please note that our equipment has not been designed for

use in commercial, trade or industrial applications. Our

warranty will be voided if the equipment is used in com-

mercial, trade or industrial businesses or for equivalent

purposes.

Commissioning

ATTENTION!! Always disconnect the power supply before

beginning any maintenance or setup work on the machine.

Mounting belt/disc sander to work bench

If your belt/disc sander is to be used in a permanent loca-

tion, it is recommended you secure it to a workbench or

other stable surface. When mounting the belt/disc sander

to a workbench, holes should be drilled through the sup-

porting surface of the workbench.

• Mark holes on workbench where belt/disc sander is to

be mounted using holes in the base as a template for

hole pattern.

• Drill holes through workbench.

• Place belt/disc sander on workbench aligning holes in

the base with holes drilled in the workbench.

• Insert bolts (not included) and tighten securely with

lock washers and hex nuts (not included).

Note: All bolts should be inserted from the top. Install the

lock washers and hex nuts from the underside of the work-

bench.

Clamping belt/disc sander to work bench

• If your belt/disc sander is to be used as a portable

tool, it is recommended you fasten it permanently to a

mounting board that can easily be clamped to a work-

bench or other stable surface.

The mounting board should be of sufﬁcient size to avoid

tipping while belt/disc sander is in use. Any good grade

plywood or chipboard with a 3/4 in. (19 mm) thickness

is recommended.

• Mark holes on board where belt/disc sander is to be

mounted using holes in the base as a template for hole

pattern.

• Follow last three steps in section Mounting Belt/Disc

Sander to Workbench.

If lag bolts are used, make sure they are long enough to

go through holes in belt/disc sander base and material the

belt/ disc sander is being mounted to. If machine bolts are

used, make sure bolts are long enough to go through holes

in belt/disc sander, the material being mounted to, and

the lock washers and hex nuts.

Connection to vacuum suction.

The use of an extraction system is recommended.

Tool changes, Fig. 2–7

ATTENTION!! Turn off the machine and disconnect the

main plug.

When changing tools make sure to have all parts cleaned.

Prepare the appropriate tool and mount it as follows:

1. Attach the lower spindle disc (16) to the spindle (4)

(ﬁg.2).

2. Insert the table inlays (5) into the table (ﬁg. 3).

3. Attach the lower spindle disc (6) to the spindle (4)

(ﬁg.2).

4. Slide the abrasive sleeve (7) onto the rubber sleeve (6)

(ﬁg. 5).

5. Apply the disc (13) (use the correct measurements) (ﬁg.

6).

6. Put on the hex-nut and tighten it with the hook wrench

(14). (ﬁg. 7)

Be sure always to mount the correct parts when changing

the abrasive sleeves. The table inlays have to be bigger

than the abrasive sleeves. (ﬁg. 8)

Note! The 13mm abrasive sleeve is put directly onto the

spindle (4).

Table:

Abrasive sleeve

inside D

Table inlay inside

Spindle disc size

13 mm 18 mm small 16 mm

19 mm 25 mm medium 20 mm

26 mm 31 mm medium 20 mm

38 mm 44 mm large 35 mm

51 mm 57 mm large 35 mm

76 mm 82 mm large 35 mm

Initial operation

After completing all assembly and setup work, turn on the

machine and while it idles, check that the spindle can

move faultlessly. In the case of disturbances, turn the ma-

chine off immediately and rectify the cause.

Once the machine has reached its maximum revolution

speed you ay start the grinding work.

Move the work piece slowly in the direction contrary to the

running direction of the grinding roll.

Scheppach OSM100 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info