Bedienungsanleitung Scheppach OX 7-1020 (Seite 22 von 53) (Deutsch, Englisch, Französisch)

781949

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

damaged.

• The tractor must have a ow connection

and a load-free return connection.

• Ensure proper connection of the hoses.

• Hydraulic hoses shall be stored in the inten-

ded repository.

Operation with PTO

• Before connecting the machine to the

three-point hitch of the tractor, make sure

that the weight of machine is within the

tractor’s specications. The weight of the

machine can be found on the manufacturer

type plate

• Make sure that the machine is connected

correctly to the three-point hitch and that

the safety bolts are always in place. The

upper link only in higher hole. The lower

hole is for the driving devise.

• When working, be careful in order to pre-

vent accidents or damages.

• Only connect the drive shaft only to the

engine of the tractor when it is not running.

• Use only drive shafts that are approved and

suitable for the use with the log splitter.

Furthermore the drive shaft must be equip-

ped with all safety mechanisms, which

must be in good condition.

• Keep away from the drive shaft when it is

in use.

• Make sure that the shaft speed of the trac-

tor does not exceed the value specied on

the type plate (max 300 rpm).

• It is recommended to wear earplugs or

equivalent hearing protection.

• Do not operate the machine indoors. The

exhaust fumes are harmful to health. They

can cause unconsciousness and there-

fore pose a threat to the operator. If it is

necessary to work indoors or in covered

surroundings, make sure that there is suf-

cient ventilation. Do not inhale the exhaust

fumes!

Modications of any kind to the machine are

prohibited!

• For specic instructions regarding the drive

shaft, refer to its user manual (delivered

with the drive shaft).

• For maintenance work or if the splitting

wedge is stuck, disconnect the machine

from the tractor rst, after stopping the

tractor.

Never leave the machine unattended while it

is still connected to the power source!

Using the log lifter

General information on the log lifter:

• The log lifter is ready for operation

• If not used, the log lifter must be in the up-

per position. (Insert the hitch pins in the top

hole; Fig.9 „A“) It can then be used as a

second protection handle preventing lateral

displacement of the log.

• For safety reasons, only the last link of

the log lifter‘s chain will be attached to

the suspension plate.

• Make sure that nobody is present in the

working area of the log lifter

Using the Log Lifter:

• Pull the hitch pin from the lever fastener so

that the lever tube can move freely

• The stand must be in the lowest position

and must be secured with the hitch pin

(hole „B“, Fig.9).

• Guide the froe downwards until the lever

tube of the log lifter completely rests on the

ground. (Actuate the froe‘s backstop so

that the froe remains in this position,

see Working Instructions)

• In this position, you can roll the log to be

split on the lever‘s tube (The log must

be placed between the two fastening

points)

• Now unlock the froe‘s backstop (See: Wor-

king Instructions) and guide the splitting

wedge upwards. (Caution! Do not stand

in the working area of the log lifter! Risk

of injury!)

• Now align the log and split it (See: Working

Instructions)

• Take the log lifter back, or use it as a se-

cond protective arm

Notes on retracting the log lifter:

• Slightly guide the froe back (approx. 30

cm) and then actuate the backstop (See:

Working Instructions)

• Now slightly lift the lever‘s tube of the log lif-

ter with your hand (Fig.9, „A“), then lift the

grid on the lever‘s tube so that the grid can

rest on the edge of the lever‘s fastener. (Al-

ways guide the lever‘s tube manually)

• Now unlock the backstop (See: Working

Instructions), then guide the froe comple-

tely downwards again. (Until the log lifter

lies on the ground)

Transport Position of the Log Lifter:

• Guide the log lifter upwards with your hand

until it clicks into place.

• Flap the stand (Fig.9, „D“) to the top, until

it reaches a vertical position.

• Now insert the hitch pin in the hole (Fig.9,

„E“) aligned with the hole of the stand,

then secure the stand using the cotter pin

(guide the chain with the cotter pin behind

the lever‘s fastener)

Follow these instructions to ensure a fast

and reliable work.

Electrical connection m

Inspect the power cords regularly for damage.

Make sure that during this inspection the power

cord is not connected to the mains supply.

The power cords must comply with the appli-

cable VDE (German Association for Electrical,

Electronic, and Information Technologies) and

DIN (German Institute for Standardization) regu-

lations. Use only power cords with the designa-

tion H 07 RN.

A type label on the power cord is prescribed.

Faulty power cords

Power cords often suffer insulation damages.

Causes are:

• Pinching, when power cords are routed

through windows or door cracks.

• Bending due to improper attachment or

routing of the power cords.

• Cuts due to driving over the power cords.

• Insulation damages caused by yanking it

out of the power outlet.

• Cracks in the insulation because of ageing.

Such faulty power cords must not be used and

are, due to the damaged insulation, a danger

to life!

Three-phase motor 400 V/ 50 Hz

Power supply 400 volts / 50 Hz.

Power cord and extension cord must have 5

conductors

= 3 P + N + PR. - (3/N/PE).

The extension wires must have a cross-section

of at least 2.5 mm² and must not be longer than

20 m.

The power supply must be protected by a 16 A

(or less) circuit breaker.

After connecting the power supply or after

relocating, check the direction of rotation. Invert

polarity if necessary.

Turn the polarity inverter inside the power plug.

Maintenance

Retooling, adjustment and cleaning activities

are only to be carried out when the motor is

switched off.

Unplug the mains plug.

Experienced craftsmen may perform minor

repairs themselves.

Repair and maintenance activities on the

electric equipment may only be carried out

by an electronics specialist.

All protection and safety appliances must be

tted immediately after completion of repair and

maintenance work.

We recommend:

• Clean the machine thoroughly after each

use!

• Splitting knife The splitting knife is a

consumable which might need regrinding/

re-sharpening or which has to be replaced

with a new one.

• Two-hand operating facility

The control and operating facility must

remain smooth-running. Lubricate occasio-

nally with a few drops of oil.

• Movable parts

DGB

Scheppach OX 7-1020 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info