Bedienungsanleitung Scheppach OX 7-1620 (Seite 23 von 53) (Deutsch, Englisch, Französisch)

781951

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

- Keep the splitting knife guides clean.

(dirt, splinters, bark, etc.)

- Lubricate slide bars with spray oil or grease

• Check oil level of hydraulics

Check hydraulic connections and screws

for tightness and abrasive wear. If neces-

sary retighten the screw connections.

When do I change the oil?

First oil change after 50 operating hours, then

always after 250 operating hours.

Check the oil level.

Check the oil level frequently before each start-

up. If the oil level is too low, the oil pump may be

damaged.

Note: The oil level must be checked while the

splitting knife is retracted. The oil dipstick is

located on the splitting column in the ller plug

A (Fig. 5) und is provided with 1 slot. If the

oil level is at the lower end of the dipstick, this

indicates that the minimum oil level has been

reached. If this is the case, the oil must be

relled immediately. The slot indicates the maxi-

mum oil level.

The oil tank is situated in the splitting column

and is lled with high-quality hydraulic oil by the

manufacturer.

Change of the hydraulic oil and the oil lter.

Place a container under the suction hose.

Remove the hose clamp of the pump and pull off

the suction hose. Caution: allow the oil to ow

into the container! Fig. 7

Remove the suction hose completely and by

slightly tilting, allow the remaining oil to drain

into the container.

To change or clean the lter, remove the entire

intake manifold by means of a at spanner

SW41 or pipe wrench! Fig. 7.1

Clean the lter and re-mount with new sealing

tape, item no.: 1607 0333. Connect the suction

hose again and secure with hose clamps.

Remove the ller plug and ll with new hydraulic

oil.

Attention! Make sure that no dirt particles

enter the oil tank.

Dispose of used oil accordingly by taking it

to the local waste oil collection points. It is

prohibited to drain used oil into the soil or to

mix it with waste.

We recommend the following hydraulic oils:

Q8 Haydn 46

Aral Vitam gf 22

BP Energol HLP-HM 22

Mobil DTE 11

Shell Tellus 22

or equivalent.

Do not use other oil grades! The use of other

oil types affects the function of the hydraulic

cylinder.

Only when operated by PTO: change the oil of

the transmission gearing after the rst 35 opera-

ting hours, then after 1,000 operating hours or at

least once per year. Ensure that the connections

of the hydraulic system do not leak.

Hydraulic system

The hydraulic system is a closed system with oil

tank, oil pump and control valve.

The factory-made and completed system must

not be modied or re-engineered.

Check the oil level frequently.

Too low an oil level may damage the oil pump.

Check the hydraulic connections and screws for

tightness frequently – retighten if necessary.

Prior to maintenance and checking procedures,

clean the work space and have appropriate tools

in good condition to hand.

The above-indicated time intervals refer to

normal terms of use; if the machine is exposed

to heavy load, those time intervals decrease

accordingly.

Clean the machine casing, the panels and the

control levers with a soft, dry cloth that you can

moisten a little with a neutral cleaning agent.

Do not use alcohol or benzene since they might

damage the surfaces.

Keep oil and lubrication grease out of the reach

of unauthorised personnel. Read the instruc-

tions on the containers carefully and observe

them strictly. Avoid skin contact and rinse well

after use.

Troubleshooting

In cases of errors not mentioned below, please contact the customer service of the company scheppach.

Error Possible causes Solution Degree of danger

The hydraulic pump does

not run

No voltage Check whether the conductors

have power supply

Danger of an electric shock

This work process must be

performed by a maintenance

electrician.

The thermo-switch of the motor has

turned itself off.

The thermo switch turns on again

when the motor has cooled down.

The motor can be re-started.

–

The column does not

move downwards

Low oil level Check the oil level and rell Danger of contamination!

This work process can be carried

out by the machine operator.

2-manual shift not correct Check the xing of the levers Risk of being cut!

Dirt in the column guide Clean the column

Motor starts but the

column does not move

downwards

Incorrect rotating direction of the

motor during three-phase current

Check rotating direction of the

motor and shift to correct direction

Incorrect rotating direction can

damage the pump

Maintenance and repairs

All maintenance procedures must be performed

by qualied personnel under strict observation of

the available operating manual.

Prior to each maintenance, all possible

precautions must be taken; turn off the motor

and disconnect the power supply (if necessary,

unplug the power plug). Place a sign on the

machine which explains the outage of the device

“Machine out of service due to maintenance:

unauthorized persons are not allowed to start up

the machine or to remain in close proxim.

DGB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach OX 7-1620 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info