Bedienungsanleitung Scheppach OXT500 (Seite 5 von 12) (Englisch)

781931

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

english 5

Setup

Prepare the workplace where the machine is to be placed.

Ensure sufﬁcient room to allow safe work without malfunc-

tions.

The machine is designed to operate on a level surface and

mustbeplacedsecurelyonrm,levelground.

Please make sure your scheppach machine is placed ﬁrmly

on stable plain ground.

Assembly

Forpackagingreasons, thebase(6)istobeinstalledby

the customer.

Usethe5saucer-headscrewsM8x12thatareincludedin

the delivery.

Placethedevicehorizontallyontheoor,andputtheSty-

ropor pad of the packaging underneath the splitting wedge

side.

m Electrical connection

The installed electric motor is completely wired ready for op-

eration.

The customer’s connection to the power supply system, and

any extension cables that may be used, must conform with

local regulations.

Important remark:

The motor is automatically switched off in the event of an

overload. The motor can be switched on again after a cool-

ing down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation dam-

age.

Possible causes are:

• Pinch points when connection cables are run through

window or door gaps.

• Kinksresultingfromincorrectattachmentorlayingof

the connection cable.

• Cuts resulting from running over the connecting cable.

• Insulationdamageresultingfromforcefullypullingout

of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not be

used as the insulation damage makes them extremely haz-

ardous.

Check electrical connection cables regularly for damage.

Make sure the cable is disconnected from the mains when

checking.

Electrical connection cables must comply with the regula-

tionsapplicableinyourstate/localjurisdiction.

Single-phase motor

• The mains voltage must coincide with the voltage speci-

edonthemotor’sratingplate.

• Doubleinsulatedtools areequipped withapolarized

plug(onebladeiswiderthantheother.)Thisplugwill

tinapolarizedoutletonlyoneway.Iftheplugdoes

not t fully in the outlet, reverse the plug. If it still

does not t, contact a qualied electrician to install

apolarizedoutlet.Donotchangethepluginanyway.

Warning: Do not permit ﬁngers to touch the terminals of

plug when installing or removing from outlet.

• Double insulation eliminates the need for the three

wire grounded power cord and grounded power sup-

plysystem.Beforeplugginginthetool,becertainthe

outlet voltage supplied is within the voltage marked on

the nameplate.

• The connection to the mains must be protected with a

16 A slow-acting fuse.

Extension cords

• The use of any extension cord will cause some drop in

voltage and loss of power.

• Wiresoftheextensioncordmustbeofsufcientsize

to carry the current and maintain adequate voltage.

• Use the table to determine the minimum wire size

(A.W.G.)extensioncord.

• Iftheextensioncordisworn,cut,ordamagedinany

way,replaceitimmediately.

EXTENSIONCORDLENGTH

Wire Size A.W.G.

Upto58ft. 18

25 to 100 ft. 16

100 to 150 ft. 14

Note: Usingextensioncordsover150ft.longisnotrec-

ommended.

Only a qualiﬁed electrician is permitted to connect the

machine and complete repairs on its electrical equip ment.

Intheeventofenquiriespleasespecifythefollowingdata:

• Motor manufacturer

• Type of current of the motor

• Datarecordedonthemachine’sratingplate

• Datarecordedontheswitch’sratingplate

.Operation

Before operating your scheppachmachine,the bleed screw

should be loosened by some rotations until air can go in

and out of the oil tank smoothly. Failed to loosen the bleed

screw will keep the sealed air in hydraulic system being

compressed after being decompressed. Such continuous

compression/decompressionwillblowoutthesealsofthe

hydraulic system and cause permanent damage to your

scheppach machine.

Before moving your scheppach machine, make sure the

bleed screw is tightened to avoid oil leaking from this

point.

Only split plain cut log.

1.Placethelogplainontotheworktable(3).

2. Fix the log pusher in the required position according to

the length of the log.

Position 1: Length up to 201/2”,

Position 2: Length up to 181/2”,

Position 3: Length up to 161/2”.

3.Complyingwithregulationsandforyoursafety,thehy-

draulic log splitter features two-handed control.

 Tostartthesplittingprocess,youmustsimultaneously

press the lever (13) with your left hand and the start

button(8)intheswitchboxwithyourrighthand.

Releasing one of the two control elements will immedi-

ately stop the splitting process, releasing both control

elements will abort the splitting process.

 Thepressureplate(2)willthenmovebackintoitshome

position.

Scheppach OXT500 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info