Bedienungsanleitung Scheppach PL75 (Seite 15 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

644549

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

15GB

• The machine may only be used, maintained, and ope-

rated by persons familiar with it and instructed in its

operation and procedures. Arbitrary alterations to the

machine release the manufacturer from all responsi-

bility for any resulting damages.

• The machine may only be used with original accesso-

ries and tools made by the manufacturer.

• The machine may not be operated with sanding belts.

5. General safety instructions for pow-

er tools

• WARNING Read all warnings and instructions. Fai-

lure to apply all warnings and instructions can lead to

electrical shock, re and/or serious injury.

• Keep all warnings and instructions handy for fu-

ture consultation.

• The term “power tool” used in the warnings refers to

power tools that are connected to a source of electrical

energy (with an electrical cable)

1) Workplace safety

a) Keep your working area clean and well lit. Cluttered

or dimly lit workspaces can lead to accidents.

b) Do not operate power tools in areas where explosions

could take place, or in which ammable liquids, gases

or dust are present. Power tools can create sparks,

which can cause dust or fumes to ignite.

c) Keep children and bystanders away from the power

tool when it is being used. Distractions could cause

you to lose control over the equipment.

2) Electrical safety

a) The terminal plug of the tool must t into the outlet.

The plug may not be modied in any way. Do not use

an adaptor plug together with grounded power tools.

The original plugs and the appropriate outlets reduce

the risk of an electrical shock.

b) Avoid contact with grounded surfaces, such as pipes,

radiators, stoves and refrigerators. There is an increa-

sed risk of electrical shock, if your body is grounded.

c) Keep power tools away from rain or wet conditions.

Penetration of water into the power tool increases the

risk of electrical shock.

d) Do not use the cable for any purpose other than that

for which it was made. Do not use it to carry the tool,

hang it up, or to pull the plug out of the outlet. Keep

the cable away from heat, oil, sharp corners or parts

of the equipment that move. Damaged or entangled

cords increase the risk of electrical shock.

e) When operating the power tool outdoors, only use

extension cords that are suitable for outdoor use. The

use of an appropriate extension cord reduces the risk

of an electrical shock.

f) If the power tool must be used in a damp environment,

use a residual current protective device. The use of

such a device reduces the risk of electrical shock.

3) Personal safety

a) Be attentive, watch what you are doing and use the

power tool sensibly. Do not use power tools when you

are tired or under the inuence of drugs, alcohol or

medicines. One moment of inattention while using a

power tool can result in serious injury.

b) Wear personal protective equipment and always wear

protective glasses. Wearing personal protective equip-

ment, such as a dust mask, slip-free safety shoes, pro-

tective headwear or ear protection, depending on the

type and use of a power tool reduces the risk of injury.

c) Avoid unintentional start-ups. Make sure that the po-

wer tool is shut off before it is connected to the power

supply, or is carried. If you have your nger on the

switch of the tool while carrying it, or have the tool

turned on, or connected to a power supply, this beha-

viour can lead to accidents.

d) Remove the adjustment aides or the spanners be-

fore turning on the power tool. A tool or wrench that

is located in a rotating part of the machine, can lead

to injuries.

e) Avoid abnormal posture. Make sure that the operator

is standing rmly and can maintain balance. This al-

lows the operator to maintain control over the power

tool in unexpected situations.

f) Wear appropriate clothing. Do not wear loose clothing

or jewellery. Keep hair, clothing and gloves away from

the moving parts. Loose clothing, jewellery or long hair

can get caught in the moving parts.

g) If dust vacuums or catching systems can be installed

on the tool, make sure that these are correctly con-

nected and assembled. The use of a dust exhaust unit

can reduce hazards caused by dust.

4) Use and treatment of the power tool

a) Do not overtax the tool. Use the appropriate tool for

the work that is to be done. With the correct power

tool, you can work better and more safely.

b) Do not use a power tool where the switch is defec-

tive. A power tool that cannot be turned on and off is

dangerous and must be repaired.

c) Disconnect the plug from the wall outlet before you

make adjustments to the tool, change parts or put the

tool away. This precaution prevents inadvertent start-

ups of the tool.

d) Store power tools that are not in use out of reach of

children. Do not let anyone use the tool who does not

have experience with it, or who has not read these in-

structions. Power tools can be dangerous when they

are used by inexperienced people.

e) Take good care of your power tools. Make sure that

movable parts function properly and do not jam, see

that parts which inuence the use of the machine are

not broken or damaged. Repair damaged parts befo-

re operating the tool. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting edges sharp and clean. Properly main-

tained cutting tools with sharp cutting edges jam less

often and are easier to control.

g) Use power tools, accessories, and equipment accor-

ding to these instructions. Taking into account the wor-

Scheppach PL75 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scheppach PL75

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info