Bedienungsanleitung Scheppach PL75 (Seite 17 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

644549

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

17GB

the protective covering. Have the saw repaired before

use if the protective covering and spring do not work

perfectly. Damaged parts, sticky residuals or piles of

saw dust can interfere with the working of the lower

protective cover.

c) When making an “inserted cut” that does not descri-

be a right angle, make sure that the saw is guarded

against slipping to the side. Slippage can lead to a

saw blade jam and a kickback.

d) Do not put the saw on the workbench or the oor wit-

hout making sure that the protective cover is over the

saw blade. An unprotected, running saw blade can

move the saw against the cutting direction and saw

what is in the way. Check the delay time of the saw.

9. Additional safety instructions for all

sawing with a wedge

a) Use the right wedge for the saw blade that is in use.

The wedge must be thicker than the thickness of the

steel blade but thinner than the width of the teeth.

b) Adjust the wedge as described in the operating inst-

ructions. Incorrect thickness, position or direction can

be the reason that the wedge does not effectively pre-

vent a kickback.

c) Always use a wedge, except when making an inserted

cut. Reassemble the wedge after an inserted cut. The

wedge is in the way when making an inserted cut and

can cause a kickback.

d) In order for the wedge to be effective, it must be in the

sawing gap. For short cuts, a wedge does not work to

prevent kickbacks.

e) Never run the saw with a bent wedge. Even the smal-

lest defect can slow down the closing of the protec-

tive cover.

INSTRUCTIONS FOR ALL SAWS

• Do not use a sanding belt.

• Make sure that the wedge is adjusted so that the di-

stance to the sprocket ring of the saw blade is not

more than 5 mm and that the sprocket ring does not

stick out more than 5 mm above the lower edge of

the wedge.

• Make sure that the dust catching mechanism is cor-

rectly installed, as is described in this manual.

• Wear breathing protection.

• Only those saw blades recommended in the manual

should be used.

• Always wear ear protection.

• Replace the saw blades as described in this manual.

• The maximum cut depth is 75 mm.

If the electrical cable of this tool is damaged it must be

replaced by the manufacturer or the customer service

department or a similarly qualied specialist in order to

avoid dangers.

FURTHER SPECIAL SAFETY INSTRUCTIONS FOR

CIRCULAR SAWS

a) Only use the recommended saw blades which corre-

spond to EN 847-1.

b) Do not use sanding belts.

c) Only use the manufacturer’s original saw.

Do not use any saw blades which do not correspond

to the characteristics described in these operating ins-

tructions. Saw blades may not be brought to a stop by

pressure on the machine from the side.

Make sure that the saw blade is tightly assembled and

turns in the correct direction.

10. Special Safety Instructions

Safety instructions for circular saws

- Hold the equipment on the insulated handles, when

you undertake work in which the tool being used could

come into contact with hidden electrical wires, or its

own cable. Contact with a live power source can elec-

trify the metal parts of the tool and lead to an electri-

cal shock.

11. Technical data

Dimensions

L x W x H mm

420x300x235

Saw blade ø mm / number of

teeth

210 / 36

Thickness of saw blade 1,6

Idling speed n

4500

Mitre square 0°-45°

Depth of cut 90° mm 75

Depth of cut 45° mm 55

Weightkg 6,9

Motor V/Hz 230 / 50

Input W 1600

Protection class II

Sound pressure level

95 dB(A),

: 3 dB (A)

Sound power level

106 dB(A),

: 3 dB (A)

Typical weighted vibrations

5,72 m/s

K: 1,5 m/s

Subject to technical modications!

Warning: Noise can have adverse health effects. Should

the noise level increase above 85 dB(A), you must wear

ear protection. Should the electrical supply not be opti-

mal, then the current can drop for a short time when the

machine is turned on. This can inuence other equip-

ment (for example, the blinking of a lamp). Should the

electrical capacity have a Zmax < 0.27, such disturban-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach PL75 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scheppach PL75

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info