Bedienungsanleitung Scheppach Plana 4.0 C (Seite 15 von 36) (Deutsch, Englisch, Französisch)

782088

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

english 13

While work, the work table must be locked.

The extraction tube should be connected to the extraction hood.

When connected to the extraction unit can then be extracted.

Extraction connection caliber 100mm

Planer thicknessing – Machine adjustment, Fig. 11, Fig. 11.1

Set the work table high and open it.

Adjust the height to the highest possible.

Set a high pivot and heighten (bolt).

Attach the extraction connections and tighten the knurled

screw.

When connected to the extraction unit can then be extract-

ed.

Planer thicknessing – Table adjustment, Fig. 12

The thicknessing table can be adjusted in height by means

of the hand wheel.

The built in graduated ruler indicates the height from 5 to

180 mm for the Plana 3.0c and from 5 to 220 mm for the

Plana 4.0c.

One revolution of the hand wheel equals 2 mm.

The planer table as well as the thicknessing tables must

be kept clean all the time to avoid rests of resin on their

surfaces.

The maximum stock removal at a time is 2 mm for the

Plana 3.0c and 5 mm for the Plana 4.0c.

Adjustment of the graduated ruler:

In case of unprecision, the position of the ruler can be

repositioned. Unscrew the ﬁxing screws of the ruler, adjust

to the good position and tighten again the screws.

Automatic feeding while planing:

Fig 12.1, Fig 12.2

The automatic feeding can be engaged and disengaged.

When engaged (Fig 12.1), the wood is going to be forwar-

ded automatically which ensures a precise and continuous

working. When disengaged ( Fig.12.2) the machine works

at full capacity for surfacing. The feeder can also be disen-

gaged for security reasons.

V-belt tension motor, Fig. 13, Fig 13.1, Fig. 13.2

Warning!

•By the ﬁrst use of the machine, tension the V belts after

3 working hours, then check the tension of the belts every

40 hours and tension them again when needed.

•Unscrew the six cruciform screws of the rear cover of the

machine ,Fig.13

•Remove the cover.

Plana 3.0c : Fig 13.1

Loosen the 4 ﬁxing screws of the motor.

Use a ﬂat piece of wood to be positioned between the mo-

tor and the housing of the machine to use it as a lever

arm

Press on the piece of wood, when the tension of the belts

seems to be enough tighten the screws again.

Put the cover again in position and screws the 6 screw

Plana 4.0c : Fig 13.2

The moteur is mounted on an hinge. To tension the belts,

use the threaded shaft and the nut with counternut. Check

the tension of the belts.

Put the cover again in position.

Residual Risks

The machine is built according to the technical standard

and the recognized technical safety regulations. However,

certain residual risks can occur while operating.

• Risk of injury for ﬁngers and hands by the rotating planer

shaft during improper manipulation of the work piece.

• Injuries by a slipped work piece during improper han-

dling or manipulation, such as working without the stop-

per.

• Health hazard from dust or wood shavings.

• Always wear personal protective equipment, such as eye

protection and dust mask. Use the extraction outlet!

• Health hazard from noise. While operating, the noise

level will exceed the acceptable. Always wear personal

protective equipment, such as ear plugs.

• Hazard from electricity in case of usage of a defective

electrical power line.

• Process only selected woods without faults as: knots,

cross rifts, surface cracks. Bad wood will lead to risks

while operating.

• In addition, obvious residual risks exist despite all pre-

cautions taken.

• Residual risks can be minimized by observing the safety

warnings and using the machine in compliance with the

regulations, as well as following the operating instruc-

tions.

Electrical Connection

• Check power line. Do not use any defective lines. See

Electrical Connection.

• Observe the motor and the tool rotation direction. See

Electrical Connection Planing Machine

• Installations, repairs and servicing of the electric instal-

lation must only be done by an expert professional.

• Disconnect the machine to avoid breakdowns. Discon-

nect the power plug.

• Turn off the motor when leaving the machine. Discon-

nect the power plug.

• Disconnect from all power sources even for an insigniﬁ-

cant relocation of the machine! Before starting the ma-

chine again, connect it properly to the power source!

Connect the machine to the power source with a CEE-plug,

use 16 A to secure the cable.

Press the green button on the operating switch, the planer

shaft is running (Fig. 14).

Press the red button to turn off, the planer shaft will slow

down within 10 seconds.

Changes in rotation direction

The rotation direction must be checked when connecting

to the power or after moving the machine, if necessary the

polarity must be changed using a screwdriver (machine

socket, Fig. 15).

The installed electrical motor is connected and ready for

use. The connection meet the corresponding VDE- and

DIN-regulations. The power connection on the part of the

client, as well as the extension cables used, must meet

EVU-(Electricity Board) regulations.

Operation mode/ Power-on time

The electrical motor is sized for S1 use.

The motor shuts down on its own when overloaded, while a

winding thermostat is embedded in the motor. After cool-

ing (time can vary) the motor can be switched on again.

Scheppach Plana 4.0 C Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info