Bedienungsanleitung Scheppach PLC40 (Seite 20 von 112) (Deutsch, Englisch, Französisch, Polnisch)

781620

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

20 | GB

•         



• 

hot metal.

• Please be careful because sparks and hot materi-

als can easily fall through small gaps and openings



• 



is not visible.

• Connect the power cable using the shortest route

with a socket situated close to the workplace to pre-

vent the power cable from being spread across the

whole room and located on a surface which could



• Do not use the plasma cutter to defrost frozen

tubes.







• Do not use the plasma cutter when it is raining or

snowing.

• Wear dry insulating gloves.

• Do not touch the electrodes with bare hands.

• Do not wear wet or damaged gloves.

• Protect yourself from electric shock with insulation

against the workpiece.

• Do not open the device housing.

• Additional protection against a shock from the

mains power in the event a fault can be provid-

ed by using a fault-circuit interrupter, which is op-

erated with a leakage current of no more than 30

mA and covers all mains-powered devices in close

proximity. The fault-circuit interrupter must be suit-

able for all types of current.

• There must be means of rapid electrical isolation

of the cutting power source or the cutting circuit

(e.g. emergency stop device) which are easily ac-

cessible.

-

ting:

• Inhalation of fumes which result from plasma cut-

ting can endanger health.

• Do not keep your head in the fumes.

• Use the device in open areas.

• Only use the device in well-ventilated spaces.



• 

• 

location.

• -

stances.

• 

• 

should be present to be able to use it immediately.

Persons who operate and maintain the machine must

be familiar with the manual and must be informed

about potential dangers.

In addition, the applicable accident prevention regula-

tions must be strictly observed.

Other general occupational health and safety-related

rules and regulations must be observed.

The manufacturer does not take any responsibility for

damage caused by improper use or changes to the

machine.

The device is intended for compressed-air plasma

cutting of all electrically conductive metals.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial ap-

plications. Our warranty will be voided if the machine

is used in commercial, trade or industrial businesses

or for equivalent purposes.

5. 

• This device may be used by children aged 16 years

and older, and by persons with reduced physical,

sensory or mental capacities, or a lack of experi-

ence and knowledge, if they are supervised or have

been instructed in how to use the device safely and

understand the dangers that may arise when us-

ing it. Do not allow children to play with the device.

Cleaning and day-today maintenance must not be

performed by children without supervision.

• Repairs or/and maintenance work must only be

carried out by qualified electricians.

• Only use the cutting cable provided in the scope

of delivery.

• During operation, the device should not be posi-

-

tween other devices so that sufficient air can be

absorbed through the ventilation slats. Makes sure

that the device is correctly connected to the supply

voltage. Avoid any form of tensile stress of the pow-

er cable. Disconnect the plug from the socket prior

to setting up the device in another location.

• If the device is not in operation, always switch it

off by pressing the ON/OFF switch. Place the

electrode holder on an insulated surface and only

remove it from the holder after allowing it to cool

down for 15 minutes.

• 󰀨 -

  

       



make sure the workplace is suitable prior to using

the device.

• 

plasma cutter. If this is not possible, cover the ob-



Scheppach PLC40 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info