Bedienungsanleitung Scheppach PLC40 (Seite 23 von 112) (Deutsch, Englisch, Französisch, Polnisch)

781620

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 23

7. 

Open the packaging and remove the device care-

fully. Remove the packaging material as well as the

packaging and transport bracing (if available). Check

that the delivery is complete. Check the device and

accessory parts for transport damage. In case of

complaints the dealer must be informed immediate-

ly. Subsequent complaints will not be accepted. If

possible, store the packaging until the warranty pe-

riod has expired. Read the operating manual to make

yourself familiar with the device prior to using it. On-

ly use original parts for accessories as well as for

wearing and spare parts. Spare parts are available

from your specialized dealer. Specify our part num-

bers as well as the type and year of construction of

the device in your orders.

m ATTENTION



-



󰀨

8. Attachment /   



Connecting the cutting torch

• Insert the plasma burner plug (10a) into the plasma

burner connection socket (10) and tighten the union

nut hand-tight (see Fig. 1,3 + 4).

• Insert the plasma burner power plug (6) into the

plasma burner power socket (10) and tighten the

union nut hand-tight (see Fig. 1,3 + 4).

Connecting the ground cable

• Connect the ground terminal plug (9a) with the

ground terminal - connection socket (9). Make

       

and then turned. The connecting shaft must face

upwards when plugging in the ground cable plug

(9a). After plugging in, the connecting shaft must

be rotated in a clockwise direction until it reaches

the stop, in order to lock it in place (see Fig. 1,3 +

5). This does not require force!

Connect the compressed air hose

• Connect the compressed air hose (19) on the

back of the plasma cutter to the compressed air

connection (19a). To do so, insert the side of the

compressed air hose into the compressed air con-

nection (19a) of the plasma cutter without a quick

connector (see Fig. 9).

• The pressure can be set via the knob (21) on the

condensate separator (see Fig. 9 - 12). Select a

pressure of 4–4.5 bar.

• Always keep hands away from the work area when

the machine is running.

• 

• Touching hot parts of the device or workpiece (burn



• In case of improper protection risk of accident and



• Harmful emissions from smoke and gases if there

󰀩

extracted.

Warning! This electric tool generates an electro-



active or passive medical implants under certain

conditions. In order to prevent the risk of serious or

      

medical implants consult with their physician and the

manufacturer of the medical implant prior to operat-

ing the electric tool.

6. Technical data

Mains connection 230V ~ / 50Hz

Output 15 - 40A

On-load factor* 35% bei 40A (25°C)

20% bei 40A (40°C)

Working pressure 4 - 4,5 bar

Insulation class H

Cutting capacity

0,1 mm - 12 mm

( depending on the

material)

Material

Copper: 1 - 4 mm

Stainless steel: 1 - 8 mm

Aluminum: 1 - 8 mm

Iron: 1 - 10 mm

Steel: 1 - 12 mm

Dimensions L x W x H 375 x 169 x 250 mm

Weight 6 kg



Noise

m WARNING:     󰀨 

your health. If the machine noise exceeds 85 dB (A),

please wear suitable hearing protection.

On-load factor* = is the percentage of the operating

time, in which the machine can beused continuously

under normal temperature conditions. In relation to a

10-minute time period this means, for example, that

with a duty cycle of 20%, that it can be used for 2

minutes and then there should be a break of 8 min-

utes. If you exceed the duty cycle values then this will

trigger the overheating protection which will bring the

device to a stop until it has cooled down to the normal

working temperature. Exceeding the duty cycle val-

ues continuously can damage the device.

Scheppach PLC40 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info