Bedienungsanleitung Scheppach PS55 Redstone (Seite 18 von 32) (Deutsch, Englisch, Französisch)

782266

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

NOTE: Your plunge cut saw’s electrical system is equipped

with an undervoltage relay which automatically opens the

circuit when the voltage falls below a minimum pre-est-

ablished limit and which prevents the self-reset of ma-

chine functions when voltage returns to normal levels.

If the machine stops involutarily, do not be allarmed.

Make sure that there has not been a voltage failure in the

electrical system.

ADJUSTING

Caution: Prior to carrying out one of the following adjust-

ment steps, switch the machine off and unplug the mains

plug.

Cutting depth adjustment, Fig. 2

The cutting depth can be adjusted from 0 to 55 mm.

Unfasten the cutting depth adjustment screw (6) and set

the required depth using the scale (7) and retighten the

screw.

The dimentions on the rail shows the cutting depth with-

out rail.

Mitre settings, Fig. 3

The mitre square can be set from 0° to 45°.

Unfasten the mitre adjustment screws (8) on both sides,

set the desired mitre square on the scale (9) and retight-

en both screws.

Saw blade replacement, Fig. 4, 5, 6

Caution: Before you are going to make the saw blade change,

switch off the machine and unplug the power cord.

1 Press the plunge trigger (3), bring the saw blade into

the blade-change position (Adjustment screw for depth

of cut shall be adjusted to 25mm) and insert the hex

wrench into the blade locking screw (17).

2 Press on the shaft lock (13) and rotate the saw blade

(10) until the lock clicks into place.

3 Hold down the locking shaft (13) and open the blade

locking screw (17) counter clockwise, while keeping

the blade in the blade-changing position.

4 Remove the outer ﬂange (16) and the saw blade (10).

(Caution: risk of injuries, wear protective gloves)

5 Insert the new blade and ﬂange.

6 Screw in and tighten the saw blade locking screw while

keeping the shaft locking mechanism pressed again.

7 Set the plunge saw to its original position.

Adjusting the splitting wedge, Fig. 7

Adjust the distance between saw blade and splitting

wedge after a saw blade replacement, or whenever neces-

sary.

Put the saw in the same position as you do when replac-

ing a saw blade.

Unfasten the adjustment screw (18) using an Allen key

and set the splitting wedge 2-3 mm higher than the saw

blade, then retighten the adjustment screw.

Operations

After having performed all the above procedures and

opera tions, you may begin cutting.

m Remaining hazards

The machine has been built using modern technology in

accor dance with recognized safety rules. Some remaining

hazards, how ever, may still exist.

• The use of incorrect or damaged mains cables can lead

to injuries caused by electricity.

• Even when all safety measures are taken, some re-

maining hazards which are not yet evident may still

be present.

• Remaining hazards can be minimized by following the

instructions in „Safety Precautions“, „Proper Use“ and

in the entire operating manual.

• Do not force the machine unnecessarily: excessive

cutt ing pressure may lead to rapid deterioration of the

blade and a decrease in performance in terms of ﬁnish

and cutting precision.

• When cutting aluminium and plastics always use the

app ro priate clamps: all workpieces must be clamped

down ﬁrmly.

• Avoid accidental starts: do not press the start button

while inserting the plug into the socket.

• Always use the tools recommended in this manual to

obtain the best results from your plunge cut saw.

• Always keep hands away from the work area when the

ma chine is running; before performing tasks of any

kind release the main switch button located on the

handgrip, thus disconnecting the machine.

m Suitable use

To cut:

• Hard and soft, domestic and exotic wood both longitu-

dinally and transversally and with appropriate adjust-

ments (speciﬁc blade and clamps);

Unsuitable use

Do not cut:

• Ferrous materials, steel and cast iron or any other ma-

terial not mentioned above and in particular foodstuffs.

Start-up

Observe the safety notes in the operating instructions before

operating the machine.

REMOVAL OF PACKAGING

Remove the box used to protect the machine during

trans portion and keep it intact for future transportation

and storage.

ELECTRICAL CONNECTIONS

Check that the electrical system to which the machine is

connected is earthed in compliance with current safety reg-

ulations and that the current socket is in perfect condition.

The electrical system must be ﬁtted with a magnetother-

mal protective device to safeguard all conductors from

short circuits and overload.

The selection of this device should be in line with the

following electrical speciﬁcations of the machine stated

on the motor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach PS55 Redstone Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info