Bedienungsanleitung Scheppach SC36 (Seite 17 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Finnisch)

782005

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

17 GB

Caution! The following states how to avoid damage

to the implement and any resulting harm to people:

Take care of your implement

• Switch off the power when the implement is to be

carried across steps.

• Inspect the implement each time before it is to be

used. Never operate the implement if safety de-

vices (e.g. impact protector, parts of the cutting

facility or bolts are missing, worn out or damaged.

Check especially the power cable and starting lever

for damage. To avoid imbalance, all tools and bolts

must be exchanged as complete sets.

• Only use spare parts and accessories that have

been supplied or recommended by the manufactur-

er. The use of alien parts results in the immediate

loss of all guarantee claims. Ensure that all nuts,

bolts and screws are rmly tightened and that the

implement is in a safe working state.

• Never try to repair the implement yourself, other

than you have been trained accordingly. All work

that has not been listed in these Instructions must

only be carried out by authorised servicing agen-

cies.

• Treat the implement with the greatest care. Always

keep the tool clean for better and safer work. Follow

the maintenance instructions.

• Never overload the implement. Always work within

the specied capacity range. Do not use low-power

machines for heavy-duty work. Do not operate the

implement for purposes for which it is not intended.

Electrical safety:

Caution! The following states how to avoid accidents

and injuries due to electric shock:

• Before each use, carry out a visual inspection of

the power and extension cables for signs of dam-

age or ageing.

• If the power cable for this equipment is damaged, it

must be replaced by the manufacturer, a customer

service agent of the same or a similarly qualied

person in order to prevent hazards.

• Keep the power cable well away from the cutting

tools. Should the power cable become damaged

during work, then instantly disconnect the power

cable from the mains.

Do not touch the power cable before it has been

disconnected from the mains.

• Keep the extension cables away from the teeth.

The teeth may damage the cables and result in

contact with live parts.

• Check that the mains voltage is the same as indi-

cated on the rating plate.

• Wherever possible connect the implement to a

power socket with a residual- current circuit break-

er that has a rated current of not more than 30 mA.

• Avoid body contact with earthed parts (e.g. metal

fences, metal posts).

• Do not operate the implement if you are tired

or are lacking in concentration and after having

drunk alcohol or taken medicine. Always take a

work break in due time. Approach the work with

common sense.

• Familiarize yourself with the terrain and remain

focused on the potential hazards that you could

miss on account of the motor noise.

• Always maintain a secure footing while working,

especially on a sloping never up and down! Be

particularly careful when changing the travelling

direction. Do not work on very steep slopes.

• Always guide the implement at a walking pace with

both hands on the handle. Be especially careful

when you turn the implement around or draw it

towards you. Danger of stumbling!

• Start or actuate the starting lever with care and in

conformity with the directions in these Instructions.

• Do not tilt the implement when starting, other than

it has to be lifted. In this case tilt the implement

only to the extent that is absolutely necessary and

always lift the implement on the side that is oppo-

site to the operator.

• Never operate the implement without the attached

collection bag or impact protector. Danger of injury!

Always keep well away from the ejector opening.

• Do not operate the implement in the vicinity of in-

ammable liquids or gases as this could give rise

to the danger of a re or explosion.

Work intervals:

• After the implement has been turned off, the cutting

cylinder will continue to rotate for a few seconds.

Keep hands and feet well away.

• Only remove plant parts when the implement is

standing completely still. Ensure that the grass

ejector opening is clean and free.

• Switch off the power when the implement is to be

transported, lifted or tilted and when traversing

other surfaces than grass.

• Never leave the implement unattended at the place

of work.

• Always switch off the implement and disconnect

the power plug:

- Whenever you leave the implement

- Before you clean the ejector opening or unblock

or unclog the implement

- When the implement is not being used

- During all maintenance and cleaning work

- When the power cable is damaged or has be-

come tangled

- When the implement hits an obstruction during

work or when unusual vibrations arise. Establish

the cause and see if the implement has been

damaged. Do not repair it yourself! Have the

implement repaired by an authorised workshop!

• Store the implement in a dry place well out of reach

of children.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach SC36 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info