Bedienungsanleitung Scheppach SC36 (Seite 20 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Finnisch)

782005

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

20 GB

Cleaning and maintenance

Danger!

Always pull out the mains power plug before starting

any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents or

solvents; these could attack the plastic parts of the

equipment. Ensure that no water can seep into the

device. The ingress of water into an electric tool

increases the risk of an electric shock.

Carbon brushes

In case of excessive sparking, have the carbon

brushes checked only by a qualied electrician.

Danger! The carbon brushes should not be replaced

by anyone but a qualied electrician.

Maintenance

• A worn out or damaged cutting unit should be re-

placed by an authorised expert.

• Take care that all fastening elements (screws,

nuts, etc.) are rmly tightened, so that you can

work safely with the scarier.

• Store the scarier in a dry place.

• For longer life, all screw-fastened parts, such as

wheels and axles should be cleaned and subse-

quently oiled.

• Regular servicing of the scarier not only secures

longer endurance and performance, but also con-

tributes to an accurate and simple scarication of

your lawn.

• At the end of the season, carry out a general check

of the scarier, and remove all residue collected.

Before the start of every season, it is absolutely

necessary to check the state of the scarier. Con-

tact our Customer Service if repair work is nec-

essary.

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the

following parts are therefore also required for use

as consumables.

Wear parts*: Aerator roller, Carbon brushes

* Not necessarily included in the scope of delivery!

Danger!

The roller rotates for a few seconds after the motor is

switched off . Never attempt to stop the roller. In the

event that the rotating roller strikes an object, imme-

diately switch off the equipment and wait for the roller

to come to a complete stop.

Then inspect the condition of the roller. Replace any

parts that are damaged. Lay the power cable on the

ground in loops in front of the power outlet. Scarify

away from the power outlet and cable, making sure

that the power cable always trails in the already scari-

ed grass so that the equipment does not travel over

the cable.

Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions. The

customer‘s mains connection as well as the ex-

tension cable used must also comply with these

regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insula-

tion damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking „H05VV-F“.

The printing of the type designation on the connec-

tion cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm2.

Connections and repairs of electrical equipment may

only be carried out by an electrician.

Please provide the following information in the event

of any enquiries:

• Type of current for the motor

• Machine data - type plate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach SC36 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info