782189
29
Zoom out
Zoom in
Vorherige Seite
1/120
Nächste Seite
29
Troubleshooting table
Warning: In the interests of operational safety, always switch off the saw and remove the mains plug before carrying out
maintenance work.
Fault Possible causes Action
Saw blades break Tension incorrectly set Set the correct tension
Load to great Feed the workpiece more slowly
Incorrect saw blade variety Use the correct saw blades
Workpiece not fed straight Avoid exerting pressure from the side
Motor does not function Mains Gable faulty Change faulty parts
Motor faulty Call customer service. Do not attempt
to repair the motor yourself as this
should be carried out by trained
personnel.
Vibration
NOTE: The saw vibrates slightly
when the motor is running in normal
operation.
Saw incorrectely installed Refer to the instructions given earlier
in this manual for information on
installing the saw
Unsuitable underlay The heavier the work bench is,the
less the vibration. A bench made from
ply wood always vibrates more than
one made from solid wood. Select
the work bench best suited to your
working conditions
The work bench is not screwed down
or is on the motor
Tighten the locking lever
The motor is not secured Securely screw the motor in place
Saw blade swings out
Holders not aligned straight
Holders not aligned Losen the screws with which the
holders are fastenedto the arm.
Align the holders so that they are
perpendicular to each other and
retighten the screws.
Plan de recherche des défauts
Avertissement: Dans I‘intérêt de la sécurité du service, éteignez toujours la scie et retirez la prise de contact avant
d‘entreprendre des travaux de réparation.
Défaut Origine possible Manière de procéder
Les lames se cassent Tension mal réglée Régler la tension convenable
Charge trop forte Amener la pièce d‘œuvre plus
lentement
Type de lame incorrect Utiliser les lames convenables
Piece d‘ouvrage amenée de travers Éviter une pression latérale
Le moteur ne marche pas Câble de réseau Remplacer les pièces défectueuses
défectueux
Moteur défectueux Appeler te service clientèle. N‘essayez
pas de réparer le moteur vous même,
ceci doit être effectué par une main
d‘œuvre spécialisée autorie
Vibration
REMARQUE: La scie vibre un peu
tourne.
Scie mal montée Pour le montage de la scie, voir les
indications plus haut dans le manuel
Table inconvénient Plus la table d‘ouvrage est lourde, plus
la vibration est faible. Une table en
presspahn vibre toujours plus qu‘une
table en bois massif. Choisissez la table
qui convient à votre avis
Table d‘auvrage mal vissée au appuyée
cantre le mateur
Tirer le levier de blocage
Moteur mal vissé Fixations non mises
en place
Bien visser le moteur
La lame de scie n‘oscille pas.
Orientation de travers
Desserrez les vis avec lesquelles les
fixations sont fixees au bras
Mettez les fixations en position
verticale. Resserrez les vis.
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Scheppach SD1600F wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info