Bedienungsanleitung Scheppach SL9LXU Woodster (Seite 24 von 44) (Deutsch, Englisch, Französisch)

782501

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

24 GB/IE

6. Technical data

AC motor 220 - 240 V ~ 50Hz

Power 1500 Watt

Operating mode S1*

Idle speed n04500 min-1

Carbide saw blade ø 216 x ø 30 x 2,8

Number of teeth 24

Swivel range -47° / 0°/ +47°

Mitre cut 0° bis 45° nach links

Saw width at 90° 305 x 70 mm

Saw width at 45° 215 x 70 mm

Saw width at 2 x 45°

(double mitre cut) 215 x 35 mm

Protection class II

Weight approx. 10.5 kg

Laser class 2

Wavelength of laser 650 nm

Laser output ≤ 1 mW

* S1, Continuous duty, Continuous operation with

constant load.

The work piece must have a minimum height of 3mm

and a minimum width of 10 mm.

Make sure that the workpiece is always secured with

the clamping device.

Noise

Total vibration values determined in accordance with

EN 61029.

sound pressure level LpA 93.6 dB(A)

uncertainty KpA 3 dB

sound power level LWA 106.6 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Residual risks

The machine has been built according to the state of

the art and the recognised technical safety require-

ments. However, individual residual risks can arise

during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instruc-

tions“ and the „Proper use“ are observed along with

the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the oper-

ating button may not be pressed when inserting the

plug in an outlet.

• Use the tool that is recommended in this manual. In do-

ing so, your mitre saw provides optimal performance.

• Hands may never enter the processing zone when

the machine is in operation. Release the handle but-

ton and switch off the machine prior to any operations.

7. Before starting the equipment

• The equipment must be set up where it can stand se-

curely, i.e. it should be bolted to a workbench, a uni-

versal base frame or similar.

• All covers and safety devices have to be properly t-

ted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails or

screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power sup-

ply make sure the data on the rating plate are dentical

to the mains data.

8. Attachment and operation

8.1 Attaching the saw (Fig1/2/3/4/5)

• In order to adjust the rotary table (15) loosen the set

screw (11) approx. 2 turns.

• Turn the rotary table (15) and pointer (13) to the de-

sired angle measurement on the scale (14) and secure

with the set screw (11).

• Pressing the machine head (4) lightly downwards and

removing the locking bolt (24) from the motor bracket

at the same time disengages the saw from the low-

est position.

• Swing the machine head (4) up until the release lever

(2) latches into place.

• It is possible to secure the clamping device (7) to the

left or right on the stationary saw bench (16). Insert

the clamping device (7) into the provided hole on the

rear side of the stop rail (17) and secure it with the

wing screw.

• Attach the workpiece supports (8) to the xed saw ta-

ble as shown in Figure 4 and fasten with the screw (9).

• It is possible to tilt the machine head (4) a max. 45° to

the left by loosening the set screw (23).

8.2 Precision adjustment of the stop for crosscut

90° (Fig. 1/5/6)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (24).

• Loosen the set screw (23).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach SL9LXU Woodster Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info