Bedienungsanleitung Scheppach Structo 7.0 (Seite 15 von 42) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

782183

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

10 english

cords have to comply with the relevant VDE - and DIN r

regulations. Only use power cables with the qualiﬁcation H

07 RN. An imprint of the type denomination is rule.

Rotary current motor

• The power supply should be 400 Volt/50 Hz.

• The power supply and the extension cables must be 5-

fold leads = 3 P + N + SL.

• Extension cables must have a minimum cable cross

section of 1.5 square millimeter.

• The power supply should be maximum 16 A.

• In case of connection to the power supply or moving site

the rotary direction should be checked, otherwise the

polarity has to be changed (wall mounted connector).

Therefore screw the phase switcher into the plug

surrounding with a screw driver.

Connections and repairs of the electrical equipment should

only be carried out by an electrical specialist.

In case you have further questions, please specify the

following:

•Motor manufacturer

•Current type of the motor

•Information of the machine type label

•Information of the switch type label

When sending back the motor, always return the comple-

te power unit with switch

Implementation

Please read the safety information before implementation.

The implementation of the machine is only admissable

when protection and safety facilites have been installed

completely.

Put the machine on a stable, even ﬂoor. If necessary attach

through the bottom through the holes to the frame valves.

(screws/nails)

After connection to the power supply your scheppach

construction circular saw is ready to operate.

Longitudinal cuts, Fig. 07

For parallel cuts use the longitudinal end stop. To process

smaller workpieces (less than 120 mm) use the stick

rail.

Use end stop rail with lower end stop height. In case of

disuse take down the longitudinal end stop to the right

table side.

For cutting jobs over 120 mm use the end stop ruler with

the high end stop side (1) and for cutting jobs under

120 mm use the lower end stop side (2).

Cross cuttings, Fig. 08

For cross - and angle cuttings use the crosscut gauge.

The performance of the crosscut gauge also allows the

making of wedges. The adjust scale reaches from 0° to

90°. Introduce the slewing unit right-angled with the

sixfold screw to the saw blade.

In case of disuse deviate the crosscut gauge sideways.

A sliding table is optional.

Exchange of saw blade, Fig. 09

Be careful: pull out power plug!

• Untighten both upper screws (M8) at the lower saw blad

cover.

• Deviate saw blade cover.

• Loosen clamping nut (M20 links) and hold back with

retaining arbor.

• Wear gloves to protect your hands.

• Take out saw blade, introduce new one.

• Only put in well sharpened, crack-free and not disformed

saw blades.

• Tighten clamping nut and hold back with retaining arbor

(left-hand thread).

• Lift up the lower saw blade cover and tighten both screws

(M8) again.

• After every saw blade exchange the slit wedge has to be

re-adjusted. See slit wedge adjustment.

Maintenance

With all maintenance and cleaning works switch off the

motor and pull out the power plug.

All protection and safety facilities should be ﬁtted again

after completed repair and maintenance works.

• The circular saw is to the greatest possible extent

maintenance-free, including the electrical motor.

Excluded are the saw blades, the table insert and the

brake linings, which are subject to wear (approx.15,000

shifts) of the electrical motor. The saw blade has to stop

within 10 sec. If necessary exchange the petered-out

table insert.

• Brake pads should only be exchanged by specialized

staff.

• Keep the table surface always resin-free.

• Keep the saw blade protection box free from wood

particles and sawdust. When the power supply is pulled

out, open the protection box lid, remove possible saw-

dust remains

Accesoires

Sliding table Art.Nr. 56450701

lineal velcity Art.Nr. 53000711

Removal

On removing the machine one should unconditionally com-

ply with the local legal regulations.

(For further information contact the responsible local wa-

ste department.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Structo 7.0 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info