Bedienungsanleitung Scheppach TRW1200 (Seite 22 von 28) (Deutsch, Englisch)

781900

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

8. Assembly

1. Thread the mixing paddle (1) clockwise

into the mixing element (2). (Fig. 2)

2. Drive the assembled mixing paddle onto

the drive shaft (3). (Fig. 3)

DANGER!

Use only a mixing paddle that is de-

signed and suitable for the material to

be mixed. A wrong mixing paddle may

put strain on the power tool which may

damage the tool and lead to accidents!

Remove the mixing paddle from the drive

shaft by turning it anticlockwise. The paddle

may sit quite tight in its holding xture. If this

is the case, the xture must be secured with

a key against turning with the paddle. (Fig. 4)

m Warning!

Disconnect the machine from the power

supply before assembling or disassembling

the stirrer.

Failure to do so may result in accidental

starting and possibly serious injury.

9. Operation

Turning on (Fig. 1)

Press and hold the circuit breaker (5) for the

ON / OFF switch; now you can press the

ON / OFF switch (4) to start the handheld

mixer. Once the tool is running properly you

can release the ON / OFF switch, turning o󰀨

the circuit breaker (5).

Turning o󰀨 (Fig. 1)

Release the ON / OFF switch (4). The circuit

breaker for the ON / OFF switch (5) turns

o󰀨 automatically.

Speed controller (Fig. 5)

With the speed controller (6), the power

tool’s speed can be gradually adjusted.

The type of material to be mixed determines

the speed rate that is required. Practice will

teach you the optimal speed required by the

respective material.

7. Technical data

Nominal voltage 220-240 V~ 50 Hz

Power consumption 1200 Watt

Speed 0-700 min-1

Weight 4.8 kg

Mixer holding xture M14

Stirrer diameter 140 mm

Sound emission

Noise emission values are measured ac-

cording to the relevant standards.

Sound pressure level LpA 89 dB(A)

Uncertainty K 3 dB(A)

Sound power level LwA 100 dB(A)

Uncertainty K 3 dB(A)

Vibration ah5.67 m/s²

Uncertainty K 1.5 m/s²

• The indicated vibration emission value

has been measured using a standardized

test procedure and can be used to com-

pare one electric tool with another;

• The indicated vibration emission value

can also be used in a preliminary expo-

sure assessment.

• Depending on how the power tool is used,

the vibration emission value may di󰀨er

from the specied value when the power

tool is actually used;

• Try to keep the exposure to vibrations as

low as possible. Actions reducing the ex-

posure to vibration include, for example,

wearing gloves when the tool is used and

limiting the working time. Here, all aspects

of the operating cycle must be considered

(for example, the times when the tool is

turned o󰀨, and those when the tool is

turned on but running without load).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach TRW1200 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info