Bedienungsanleitung Scheppach TS 315 GT (Seite 6 von 28) (Alle Sprachen)

782059

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

8 english françãis 9

• Insert adjusting bolt (2).

• Attach stop track (3).

2 carriage bolts M6 x 50

2 sheet metal spacers

2 washers 6 in diam.

2 wing nuts M6

• Insert folding stop into the stop track.

Final assembly hf 3000/tfe 30, Fig. F1/F2

(1) stop tube

(2) adjusting bolt

(3) stop track

(4) plate

(5) retaining strip

(6) bearing strip

• Insert stop tube into the pivoting drill hole of the slide

table.

• Insert carriage bolt M8 x 65 from above and tighten with

washer by hand.

• Insert adjusting bolt (2).

• Attach stop track (3).

2 carriage bolts M6 x 50

2 sheet metal spacers

2 washers 6 in diam.

2 wingnuts M6

• Insert folding stop into the stop track.

• Attach plate (4) and retaining strip (5) to the table.

2 carriage bolts M8 x 25

2 serrated washers 8.2 in dia.

2 hex nuts M8

• Push bearing strip (6) between plate (4) and retaining

strip (5) and tighten the hex nuts.

Work piece clamping device, Fig. G

• Insert the clamping bolt into the slide table and tighten.

1 serrated washer 8.2 in dia.

1 hex nut M8

• Choose the appropriate drill hole according to the

pivoting direction of the stop track.

• Fasten work piece clamping device to the clamping bolt

by hand.

Notes on operation

Angle correction work piece stop, Fig. L

After making a test cut, check the angle. Loosen the cap

nut to make the necessary adjustment. The adjusting nut

(1) can be turned to the required position by hand by

pushing back the stop tube slightly. Then retighten the

cap nut and make another test cut. Repeat the correction

procedure if necessary.

Fig. M

Guiding the work piece safely is a requirement for acci-

dent-free precision work. Use the work piece clamping

device properly.

• Insert work piece

• Set clamping device onto the bolt with lever in position

(1).

• Set clamping device onto work piece with lever in

position (2) and tighten the hand grip on the bolt.

• To clamp a work piece, bring the lever into position (3).

Maintenance

Your scheppach pusher slide is practically maintenance-

free.

• Occasionally apply a few drops of oil to the work piece

clamping device.

• Replace the cleaning brush if necessary.

• Keep the ball-bearing guide of the slide table free

of sawdust and dirt by cleaning to guarantee smooth

running.

The following details are required to allow correct and fast

processing of a spare parts order:

• Machine type

• Machine number

• Description, order number for spare part

• When ordering spare parts for electric equipment, the

date shown on the nameplate of motor and switch must

be quoted.

• Quantity of the required spare part

• Exact details of address and type of dispatch

Guarantee

This appliance is covered by a 12 month’s guarantee

• The guarantee covers only material and construction

faults. Faulty parts are replaced free of charge,

customers must carry out replacement work.

• We guarantee only original scheppach parts.

• The guarantee does not cover: Transport damage, wear-

ing parts, damage resulting from improper use or failure

to observe operating instructions.

• Guarantee claims are valid only if no repairs have been

made by a third party.

• The warranty certicate is only valid with the invoice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach TS 315 GT Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info