Bedienungsanleitung Scheppach TS251 (Seite 19 von 40) (Deutsch, Englisch, Französisch)

782524

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

of 3200 ha or 2600 ha in order to remove splinters

and saw dust. The ﬂow rate at the extraction port must

be 20 m/s.

• Automatic activation is available in the special acces-

sories. Type ALV 2: Art. no. 7910 4010, 230–240

V/50 Hz

• When turning on the power tool, the extraction unit

starts up automatically after 2 – 3 seconds delay. This

prevents overloading the mains fuse.

• After turning off the power tool, the extraction unit

continues for 3 – 4 seconds and then turns off auto-

matically.

• In this way, the remaining dust is extracted as required

by the German Ordinance on Hazardous Substances.

This saves power and reduces noise. The extraction

unit is only on when the power tool is used.

• Do not switch off or remove the extraction unit or de-

duster when the machine is running.

• This power tool has been designed for the exclusive

processing of wood and materials similar to wood. On-

ly original tools and accessories may be used. Use the

required saw blade according to Standard EN 847-1

depending on the type of cut and wood (solid wood,

plywood or chipboard). Take note of the accessory parts

listed in this operating manual.

• Use the machine in a technically ﬂawless condition on-

ly, as well as for its intended purpose, in a safe manner

and being aware of dangers, in compliance with the

operating instructions. Failures which can affect safety

in particular must be removed straight away.

• The manufacturer’s stipulations concerning safety,

work and maintenance as well as the measurements

speciﬁed in Technical data, must be complied with.

• The relevant accident prevention stipulations and other

widely recognised safety rules must be observed.

• The power tool may only be used, maintained or re-

paired by expert personnel who are familiar with it and

its dangers. Unauthorised changes to the power tool

invalidate the manufacturer’s liability for damages re-

sulting from this.

• The power tool may only be used with the

manufacturer’s original accessories and original tools.

• Every use beyond that is deemed as not intended. The

manufacturer is not liable for damage resulting from

this, the risk lies exclusively with the user.

Set-up

Prepare the work place where the power tool will be used.

Make sufﬁcient space so that safe and uninterrupted work

is ensured. The power tool has been designed for work in

closed rooms, and it has to be set up on an even, level,

solid surface in a stable position.

your grip and to reduce the risk of personal injuries.

7 Before operating the insertion tool, ensure that all

protective devices are attached properly.

8 Before operation also make sure that the insertion tool

you intend to use meets the technical requirements

for electrical power tools.

9 Use the provided saw blade only for cutting wood and

never for cutting metals.

RESIDUAL RISKS

The power tool has been built according to the latest tech-

nology and recognised safety rules. However, there is still

a chance of residual risks whilst working.

• Risk of injury to ﬁngers and hands from the rotating

saw blade if the work piece is handled incorrectly.

• Injuries when the work piece is ejected during incor-

rect holding or handling, such as working without a

fence.

• Health risk from noise

• During work, the permitted noise level is exceeded.

Make sure you wear personal protective equipment

such as hearing protection.

• Injuries due to a faulty saw blade. Regularly check the

saw blade for integrity and before every use.

• Electrical hazards when unsuitable electric connec-

tions are used.

• When using special accessories, the special acces-

sories’ operating instructions must be read carefully

and followed.

• Furthermore, despite all measures taken, residual risks

can occur that are not obvious.

• Residual risks can be minimised by complying with

the safety notices and the intended use as well as the

operating instructions overall.

m Intended use

The power tool complies with the relevant EC machine gui-

deline.

• This power tool has been deﬁned as a transportable

power tool.

• To transport the power tool or change its position, hold

on to the saw bench at the front and the back and lift

the power tool.

• If the supplied frame is not used, the power tool has to

be mounted on a stable work bench. The work height

has to be 850 mm.

• As the operator, always position yourself in front of the

power tool, to the left of the saw blade.

• The work and surrounding area of the power tool have

to be free from foreign objects which could interfere,

in order to prevent accidents.

• As a basic principle, the work pieces which will be

processed have to be free from foreign objects such

as nails or screws.

• Before commissioning, the power tool has to be con-

nected to an extraction unit with a ﬂexible, ﬂame-re-

sistant extraction line. The extraction unit has to turn

on automatically when the power tool is turned on.

• If the power tool is used in closed rooms, it has to be

connected to an extraction unit. Use dust extraction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach TS251 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info