781891
23
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
23 І 36
Old devices must not be disposed of with
household waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical
and electronic equipment (WEEE). This product must
be disposed of at a designated collection point.
This can occur, for example, by handing it in at an
authorised collecting point for the recycling of waste
electrical and electronic equipment. Improper han-
dling of waste equipment may have negative conse-
quences for the environment and human health due
to potentially hazardous substances that are often
contained in electrical and electronic equipment. By
properly disposing of this product, you
are also contributing to the effective use of natu-
ral resources. You can obtain information on collec-
tion points for waste equipment from your municipal
administration, public waste disposal authority, an
authorised body for the disposal of waste electri-
cal and electronic equipment or your waste disposal
company.
13. Troubleshooting
Fault Possible cause Remedy
1. Power tool does
not start
Power supply interrupted Check power supply by connecting another
power tool
Power cord or plug defective Electrician must check the tool
Other electrical defect of the power tool Electrician must check the tool
2. Power tool
does not oper-
ate with full
power
Extension cord too long and/or cross-section
too small
Use extension cord with permissible length and/
or adequate cross-section
Power supply (e.g. generator) voltage too low Connect power tool to an appropriate power sup-
ply
3. Poor operation
results
Sanding paper worn out Replace sanding paper
Abrasive plate worn out Replace abrasive plate by specialist
4. Considerable
dust formation
Brush edge (around the sanding disc) worn out Replace brush edge by specialist
Dust extraction not connected / switched on Connect / switch on dust extraction
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brushes, Grinding plates, Brush
head, Sanding paper
* Not necessarily included in the scope of delivery!
23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Scheppach WDS 999 Kraft Werkzeuge wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info