Bedienungsanleitung Scheppach Woova 3.1 (Seite 8 von 16) (Deutsch, Englisch, Französisch)

782131

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Safety notes m

• Please pass on safety notes and instruc-

tions to all those who work on the machine.

• Observe all safety instructions and warnings

attached to the machine.

• See to it that safety instructions and wa-

mings attached to the machine are atways

complete and perfectly legible.

• Check all power supply lines. Do not use

defective lines.

• Insure that the planing machine is set up in

a sta ble position on rm ground.

• Protect the machine from moisture and

dampness.

• Keep children away from the machine when

it is connected to the power supply.

• Operating personal must be at least 18

years of age. Trainees must be at least

16 years of age,but may only operate the

machine under adultsupervision.

• Connection and repair work on the electrical

installation may be camed out by a qualied

electrician only.

• Note the motor rotationat direction – see

electrical connection.

• Switch the machine off and pull power sup-

ply plug when rectifying any malfunctions.

• Persons unfamiliar with the machine may

not operate it.

• Perform maintenance tasks, change bag, l-

ter, orhose only with mains plug unplugged.

• In hazardous locations, only special

explosion -proof devices may be operated.

Use only original accessories.

• Verify proper functioning of the machine

before each use.

• Do not use the machine at temperatures

below 0 °C, at risk of damaging the housing.

• When leaving the work place, switch the

motoroff. Pull the power supply plug.

• Cut off the external power supply of the

machine or plant even if inly minor changes

of place are envisaged. Properly reconnect

the machine to the supply mains before

recommissioning.

Use only as authorized m

The machine meets valid EC machine

guidelines.

• The machine has been built in accordance

with state-of-the-art standards and the recog-

nized safety rules. Nevertheless, its use may

constitue a risk to life and limb of the user

or of third parties,or cause damage to the

machine and to othermaterial property.

• The machine must only be used in techni-

cally perfect condition in accordance with its

designated use and the instructions set out in

the operating manual, and only by safety-

conscious persons who are fully aware of the

risks involved in operating the machine. Any

functional disorders, especially those affec-

ting the safety of the machine, should there-

fore be rectied immediately. The vacuum

exhaust unit is designed only for removing

saw dust (nor for normal dust).

• Regularly inspect the lter for damage.

• Replace damaged lters!

• Regularly check that the housing is well

sealed and regularly inspect the lter and

saw dust sackseals.

• Do not allow foreign objects such as screws,

nails, plastic or wood chips to enter the

cleaning nozzle.

• The machine must only be used with original

parts and orginal accessories supplies by the

manufacturer.

• The Exhaust System dc 12 is constructed

exclusively for exhaust-vacuuming wood

chips and saw dust and may only be used in

connection with wood processing machines.

• When vacuuming shop oors, wood or metal

pieces may not be vacuumed.

• Any other use exceeds authorization. The

manufacturer is not responsible for any da-

magesresulting from unauthorized use; risk

is the sole responsibility of the operator.

• The safety, work and maintenance instruc-

tions of the manufacturer as well as the

technical data given in the calibrations and

dimensions must be adhered to.

• Relevant accident prevention regulations and

other, generally recognized safety-technical

rules must also be adhered to.

• The machine may only be used, maintained,

and operated by persons familiar with and

instructed in its operating and procedures.

Arbitrary alterations to the machine release

the manufacturer from all responsibiliy for

any resulting damages.

• The machine may only be used with original

accessories made by the manufacturer.

Remaining hazards m

The machine has been built using modem

technology in accordance with recognized

safety rules.Some remaining hazards, how-

ever, may still exist.

• Wood chips and sawdust can be health

hazards. Be sure to wear personal protecti-

ve gear such as safety goggles and a dust

mask.

• Dust inhalation may occur when closing and

replacing the dust bag.

• Please note the instructions concerning pro-

per disposal in the operating manual (e.g.

the use of P2 dust masks) to prevent dust

inhalation.

• Noise can be a health hazard. The permit-

ted noise level is exceeded when working.

Be sure to wear personal protective gear

such as ear protection.

• The use of incorrect or damaged mains

cables can lead to injuries caused by elec-

tricity.

• Even when all safety measures are taken,

some remaining hazards which are not yet

evident may still be present.

• Remaining hazards can be minimized by

following the instructions in “Safety Pre-

cautions”, “Proper Use“ and in the entire

operating manual.

Assembly

For packaging reasons, your machine is

not completely assembled.

Fig. 2 Housing installation

Install the motor housing (1), the housing

gasket (8) and the lter housing (2) using 6

washers and 6 hex head bolts (M6x16) and

tighten securely.

Caution! Insert the housing gasket between

the motor housing and lter housing properly.

Fig. 3 Mounting frame

(To avoid damage, place styrofoam or card-

board from the packaging as a base),

Carefully place the housing on the motor and

support the lter housing with a wooden beam

(due to risk of tilting).

Mount the vertical stands (11) on both sides of

the motor housing using a clamping block (5),

2 washers and 2 hex head bolts (M8x25) and

tighten.

Fig. 4 Installation of vertical stand with

handle

Clamping block (5), vertical stand (11) and

handle (12) with 2 washers, 2 hex screws

(M8x45), 2 washers and 2 nuts (M8) on both

sides of the lter housing and tighten.

Fig. 5 Installation of base plate with guide

rollers

Mount 2 guide rollers (13) and 2 steering

rollers (14) under the base plate (10) using

4 washers and 4 Phillips screws (M5x10) for

each roller and tighten.

Place the base plate (10) on the 4 stands (11)

and x in place using 4 washers and 4 hex

head bolts (M8x10).

Make sure that the steering rollers (14) are

mounted on the handle side.

Place the exhaust ventilator carefully on the

wheels.

Fig. 6 Chip bag holder installation

Mount the chip bag holder (17) on the lter

housing (2) using 2 washers and 2 hex head

bolts (M4x10).

Figs. 7, 8 Chip bag lter installation

Tauten the chip bag (16) from below into the

clamps (A) stretch and lock using the clamping

strap (7).

Suspend lter bag (15) into the lter bag

holder (17) and draw the clamping strap (7)

through the loops (B) on the lter bag and

lock.

Scheppach Woova 3.1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info