Bedienungsanleitung Scheppach Wox D 700 (Seite 18 von 48) (Deutsch, Englisch, Französisch)

781863

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

18 GB

• Note the direction of rotation of the motor and saw

blade. Use only blades whose permissible maxi-

mum speed is not lower than the maximum spindle

speed of the circular saw and of the material to

be cut.

• After you have switched off the motor, never slow

down the saw blade by applying pressure to its

side.

• Only t blades which are well sharpened and have

no cracks or deformations.

• Only use saw blades that are recommended by the

manufacturer, comply with EN 847-1.

• Faulty saw blades must be replaced immediately.

• Never use saw blades which do not comply with

the data specied in this manual.

• Never dismantle the machines safety devices or

render them inoperative.

• If the table insert is worn, replace it.

• Always stand to the side of the saw blade when

working with the saw.

• Never load the machine so much that it cuts out.

• Make sure that off-cuts do not catch on the saw

blade crown.

• Never remove loose splinters, chips or jammed

pieces of wood when the saw blade is running.

• To rectify faults or remove jammed pieces of wood,

always switch off the machine rst. - Unplug the

power plug -

• If the sawing gap is worn, replace the table insert.

Turn off the machine and unplug the power plug.

• Carry out retooling work, adjustments, measure-

ments and cleaning jobs only when the motor is

switched off. - Unplug the power plug -

• Before switching on, make sure that all keys and

wrenches have been removed from the tool.

• Switch off the motor and unplug the power plug

before you leave the workplace

• Ret all guards and safety devices immediately

after you have completed any repairs or mainte-

nance work.

• Be sure to observe the safety information and op-

erating and maintenance instructions issued by the

manufacturer, as well as the dimensions listed in

the Technical Data.

• It is imperative to observe the accident prevention

regulations in force in your area as well as all other

generally recognized rules of safety.

• Make sure you stand squarely and keep your bal-

ance at all times.

• Check the tool for damage!

• Each time before re-using the tool, carefully check

that the guards or any slightly damaged parts are

working as intended.

• Check that the moving parts are in good working

order, that they do not jam, and that no parts are

damaged. Make sure that all parts are tted cor-

rectly and that all other operating conditions are

properly fullled.

• Unless otherwise stated in the operating instruc-

tions, damaged safety devices and parts must be re-

paired or replaced by an authorized service center.

• This tool conforms to the applicable safety regula-

tions. Repairs may only be performed by a special-

ist using original spare parts. Otherwise accidents

could occur.

• If necessary, wear suitable personal protection

equipment. This could consist of:

- Ear plugs to prevent the risk of damaging your

hearing;

- A breathing mask to avoid the risk of inhaling

hazardous dust.

- Always wear gloves when handling saw blades

and rough materials. Whenever practicable, saw

blades must be carried in a container.

• The operator must be informed about the condi-

tions that inuence the generation of noise (for

example saw blades designed to reduce noise

emissions, caring for blades and the machine).

• Faults on the machine or its guards, safety devices

and blade must be reported to the person in charge

as soon as they are discovered.

• Use only the transport devices to move the ma-

chine. Never use the guards for handling and mov-

ing the machine.

• All operators must receive proper training in the

use, adjustment and operation of the machine.

• Do not saw any materials that contain foreign bod-

ies such as wires, cables or ties.

• Only use sharp saw blades.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair active

or passive medical implants under certain conditions.

In order to prevent the risk of serious or deadly injuries,

we recommend that persons with medical implants

consult with their physician and the manufacturer of

the medical implant prior to operating the electric tool.

3. Use only as authorized

The rewood circular saw is designed exclusively

with the offered tool for the processing of wood.

The machine corresponds to the valid EC guide-

line.

• The log saw is constructed as 1-man-operating

stand and is only to be used in outdoor locations.

• The log saw is a portable circular saw. It is only ap-

plicable to cross cut rewood with a feeding rocker

according to the technical specications.

• The saw is constructed solely for cross cutting of

rewood with max. 1 meter length.

• Regardless of the diameter of the wood only 1

work piece is to be put on the rocker.

• Observe all safety and hazard notes on the ma-

chine and ensure they are kept complete and in a

legible condition.

• Observe all safety and hazard notes on the ma-

chine and ensure they are kept complete and in a

legible condition.

Scheppach Wox D 700 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scheppach Wox D 700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info