Bedienungsanleitung Scheppach Wox D 700 (Seite 26 von 48) (Deutsch, Englisch, Französisch)

781863

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

26 GB

Keep oils and lubricants out of reach of unauthor-

ised persons. Read through the instructions on the

containers carefully and follow them closely. Avoid

direct contact with the skin and wash off thoroughly

after use.

m Check all safety devices after maintenance

and cleaning work.

Maintenance

Turn the engine off and let the engine cool down.

Re-t the mains plug.

Check the general condition of the machine. Be care-

ful with loose screws, misaligned or moving parts,

breakage of parts, and any other condition that could

interfere with safe operation.

Remove any foreign objects and other materials

that have accumulated on the saw blade and the

unit. Clean the machine after each use. Then use a

high-quality and thin uid machine oil to lubricate all

moving parts.

m Never use a “pressure washer” to clean your

unit. Water can penetrate tight areas of the

machine and its transmission case and cause

damage to spindles, gears, bearings, or the

engine. The use of pressure washers will result

in shortened life and reduce serviceability.

Experienced craftsmen can perform minor repairs

on the machine itself.

• Check the saw blade regularly. Use only

well-sharpened, crack-free and not distorted saws.

Use only tools that comply with the European

standard EN 847-1.

• Exchange immediately rocker that run out.

• Check all safety installations after each mainte-

nance and cleaning activities.

• Ensure that there are no tools or other materials on

or in the machine before putting it into operation.

• Remove possible sawdust blockages at the dis-

charge.

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the

following parts are therefore also required for use

as consumables.

Wear parts*: sawblade; seesaw inserts

* Not necessarily included in the scope of delivery!

15. Exchange of saw blade

• The exchange of the saw blade can only be under-

taken in rewood cut position.

• Loosen the top and bottom screws on the protec-

tive cover approx. 5 mm and open the protective

cover.

• To lock the saw blade into place, insert the locking

pin (1) through the corresponding opening on the

saw blade guard. To do this, insert the pin com-

pletely and straight into the hole. Use the corre-

sponding hole (depending on the saw blade type)

so that the pin is at the lowest point (bottom of the

tooth).

• Loosen the saw blade with the supplied open-end

spanner / Allen wrench (2).

• Remove the saw blade ange

• Insert the new saw blade.

• Mount the saw blade ange again and tighten the

clamp screw.

• Remove the locking pin.

m Attention! When installing the saw blade, pay

attention to the correct direction of rotation!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Wox D 700 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scheppach Wox D 700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info