Bedienungsanleitung Schneider Electric Merten Argus 544890 (Seite 5 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

739111

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

– If possible, install the device on the north- or east-

facing wall of the building.

– If possible, install the device under roof overhangs

or similar covering.

– If possible, the connection line should be inserted

into the device from below. If the connecting cable

enters into the device from above, particularly good

insulation must be ensured.

– Install the load to be switched (lighting) in such a

way that the light from it does not fall on the light

sensor (Fig.!E). Otherwise, the sensor will not

be able to calculate the ambient brightness

correctly (optical feedback).

Tips on choosing the right installation site

V5448_581_01.book Seite 19 Mittwoch, 26. Oktober 2005 12:55 12

Risk of fatal injury

from electrical current.

The light-sensitive time switch may only be

installed and connected by skilled electricians.

Please observe the relevant regulations in your

own country.

Installing the light-sensitive time switch and taking it

into service is done in several stages, and these must

be carried out as described below.

Installing the housing and wiring the connections

1Open the housing by unscrewing the two screws at

the front. Pull out the light-sensitive time switch.

The condensation water opening on the underside of

the housing must be opened. Exception: If operated in

How to mount the light-sensitive time

switch

V5448_581_01.book Seite 20 Mittwoch, 26. Oktober 2005 12:55 12

rooms subject to a large amount of dust, it must remain

closed.

2Push open the condensation water opening (Fig.

(A, view from rear) from the inside to the outside

and break out the device wall.

3Fasten the housing to the building wall through the

openings (Fig. !E and „E) using suitable fixing

material (e.g. dowels and screws). The "OBEN/TOP"

marking should be at the top.

If you want to lead the cable into the housing from

below rather than above:

4Swap over the lead-in guides (Fig. / A/B).

5Wiring the light-sensitive time switch for the desired

application:

–Figure %: Light-sensitive time switch A with load

B and On/Off switch C (optional).

V5448_581_01.book Seite 21 Mittwoch, 26. Oktober 2005 12:55 12

–Figure &: Light-sensitive time switch A with load

B, On/Off switch C (optional) and two-way

switch D for toggling between manual and

automatic operation.

6Insert the light-sensitive time switch into the

housing and screw the housing together.

Setting the twilight threshold

|Note: To set the twilight threshold, the device

housing must be open. Make sure that the light

sensor is not covered and that no light other than

the ambient brightness falls on the lights sensor.

1Turn the setting switch for switch-on time (Fig !C)

to position "T".

V5448_581_01.book Seite 22 Mittwoch, 26. Oktober 2005 12:55 12

On reaching the threshold value required:

2Slowly turn the setting switch for the twilight

threshold (Fig !A) until the light switches on.

Leave the setting switch at this position.

3Turn the setting switch for switch-on time (Fig !C)

to position "A".

Setting the twilight function

If you want to set the threshold function (switching on

and off at dusk/dawn, Fig. „):

1Turn the setting switch for switch-off time (Fig !B)

to position "D".

2Turn the setting switch for switch-on time (Fig !C)

to position "A".

V5448_581_01.book Seite 23 Mittwoch, 26. Oktober 2005 12:55 12

Setting the automatic function

If you want to set the automatic function (time switch

evening and morning, Fig. §):

1Read off the local time deviation from the table (see

next section) and calculate the switch-on or switch-

off time.

2Turn the setting switch for switch-off time (Fig !B)

to the newly calculated switch-off time, e. g. 21:30.

3Turn the setting switch for switch-on time (Fig !C)

to the newly calculated switch-on time, e. g. 5:15.

Semi-automatic function

If you want to set the semi-automatic function (time

switch evening only, Fig. $):

1Read off the local time deviation from the table (see

next section) and calculate the switch-on time.

V5448_581_01.book Seite 24 Mittwoch, 26. Oktober 2005 12:55 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Schneider Electric Merten Argus 544890 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info