Bedienungsanleitung Schneider Electric MTN507501 (Seite 2 von 2) (Englisch)

612455

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

V5075-561-00 09/08

Resetting to factory settings (Reset)

Under certain circumstances, it is necessary to reset this

device (and possibly the other devices in the radio sys-

tem) to its factory settings and to reconfigure the radio

system:

CAUTION

When you reset to the factory settings, all the set-

tings and connections for this CONNECT device

are lost. The radio system may no longer work

and will need to be reconfigured: see the sepa-

rate description of the CONNECT radio system

(supplied with devices with system administra-

tion).

1 Using an insulated tool such as an insulated phase

tester, tap switch button B three times in quick suc-

cession (within approx 1.5 seconds).

LED A flashes at one-second intervals.

2 Then press and hold the switch button until the LED

stops flashing (approx. 5 seconds).

The device has now been reset to its factory settings.

Notes for experienced users who want to use this device

with Z-wave compatible devices from other manufactur-

ers:

Technical data

Connected loads: AC 230 V, 10 A; cos ϕ = 0.6

Allowed loads: 2000 W (incandescent lamps

230 V)

1500 W (halogen lamps 230 V)

35 µF (capacitive load in lumi-

naires with electronic transform-

er)

Type of protection: IP 20

Radio frequency: 868 MHz

Radio protocol: Z-wave

CONNECT device

type: Receiver

Range: up to approx. 100 m outdoors

up to approx. 30 m in buildings

(depending on building materi-

als)

Dimensions

(H x W x D):

approx. 48 x 52 x 27 mm, without

connecting cables

Z-wave device type Routing slave

Learn -Mode:

(for integration into Z-

wave systems of other

manufacturers)

Triple click on the switch button

Send “Node info

frame”

Triple click on the switch button.

List of functions Parameter number

Staircase timer 176, 177

Additional limit duration

(after brief interruption)

183

This device can be used with al devices that are

compatible with Z-Wave; this also applies to de-

vices from other manufacturers. Each Z-Wave-

compatible device can be added to a Z-Wave sys-

tem, in which case it then also functions as a rout-

er providing command forwarding is supported.

Configuration of a Z-Wave system is described in

the description of devices with system adminis-

tration (e.g. CONNECT radio push-button).

Some functions are only possible with devices

that are compatible with the CONNECT radio sys-

tem.

If you have technical questions, please contact the Cus-

tomer Care Center in your country.

www.schneider-electric.com

This product must be installed, connected and used in

compliance with prevailing standards and/or installation

regulations. As standards, specifications and designs

develop from time to time, always ask for confirmation of

the information given in this publication.

Z-wave designation CONNECT designation

Inclusion Teach (sends Node info frame),

see CONNECT radio system

description

Exclusion Reset to factory settings; com-

plete programming

Primary Device with system administra-

tion

Schneider Electric Industries SAS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Schneider Electric MTN507501 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Schneider Electric MTN507501

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info