Bedienungsanleitung Scholtes fm 8861 mt (Seite 15 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

330643

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Electrical connections

! Ovens equipped with a three-pole power supply

cable are designed to operate with alternating

current at the voltage and frequency indicated on

the data plate located on the appliance (

see below

Fitting the power supply cable

1. Open the terminal

board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(

see diagram

2. Loosen the cable

clamp screw and

remove it, using a

screwdriver as a lever

(see figure).

3. Remove the wire

contact screws L-N-

, then fasten the wires

under the screw heads,

respecting the colour

code: Blue (N), Brown

(L) and Yellow-Green

Verde (

Connecting the supply cable to the mains

Install a standardised plug corresponding to the

load indicated on the data plate (

see side

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum

contact opening of 3 mm installed between the

appliance and the mains, suitable for the load indicated

and complying with current electrical regulations (the

earthing wire must not be interrupted by the circuit-

breaker). The supply cable must not come into contact

with surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical

connection has been made and that it is compliant

with safety regulations.

Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is

compliant with the law.

• The socket can withstand the maximum power of

the appliance, which is indicated on the data plate

(

see below

• The voltage must be in the range between the

values indicated on the data plate (

see below

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only (

see Assistance

! The manufacturer declines any liability should

these safety measures not be observed.

DATA PLATE

Dimensions

widt h 43. 5 cm

height 32 cm

dep th 40 cm

Volume lt. 56

Ele ctric al

connections

voltage: 220-240V ~ 50Hz

maximum power absorbed

2800W or 2560-3050W (see data

late

)

ENERGY LABEL

Directive 2002/40/EC on the label

of electric ovens.

Standard EN 50304

Energy consumption for Natural

convection – heating mode:

Convection mode.

Declared energy consumption for

Forced convection Class – heating

mode: Rotisserie.

Thi s appli ance conforms to the

following European Economic

Community directives:

2006/95/EEC of 12/12/06 (Low

Voltage) and subsequent

amendments;

- 2004/108/EEC of 15/12/04

(Electromagnetic Compatibility) and

subseq uent amendme nts;

- 93/68/EEC of 22/07/93 and

subseq uent amendme nts.

- 2002/96/EC and subsequent

amendments.

- 1275/2008 stand-by/off mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scholtes fm 8861 mt Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info