Bedienungsanleitung Scholtes HDB 9 (Seite 11 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

491213

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

a. Rest the suction unit on a flat surface and thread

the lower part of the hood onto it.

b. Make all the electrical connections between the two

parts.

c. Fix the hood definitively to the suction unit with the

number and type of screws indicated in the figure.

1. Using a pencil, draw a line on the wall, extending

up to the ceiling, to mark the centre. This will

facilitate installation.

2. Rest the drilling template against the wall: the

vertical centre line printed on the drilling template

must correspond to the centre line drawn on the

wall, and the bottom edge of the drilling template

must correspond to the bottom edge of the hood.

3. Rest the support bracket on the drilling template so

that it coincides with the dotted rectangle, mark the

two outer holes and drill them, remove the drilling

template, insert 2 wall plugs and fix the hood

support bracket into place using two 5x45mm

screws.

4. Hang the hood on the bracket.

5. Adjust the distance of the hood from the wall.

6. Adjust the horizontal position of the hood.

7. Using a pencil mark the cooker hood permanent

drill hole inside the suction group (two drill holes

are necessary for fastening).

8. Remove the hood from the bracket.

9. Drill at the point marked (Ø8mm - see operation 7).

10. Insert 2 wall plugs.

11.Rest the chimney support bracket „G“ against the

wall, touching the ceiling. Use the support bracket

as a drilling template (the small slot formed on the

support must coincide with the line drawn on the

wall as above – operation 1) and mark 2 holes with

a pencil, drill the holes (Ø8mm), insert 2 wall plugs.

12.Fix the chimney support bracket to the wall using

two 5x45mm screws.

13.Hook the hood onto the bottom bracket.

14.Fix the hood into its final position on the wall

(ABSOLUTELY ESSENTIAL).

15.Connect a pipe (pipe and pipe clamps not

provided, to be purchased separately) for

discharge of fumes to the connection ring located

over the suction motor unit.

If the hood is to be used in ducting version, the

other end of the pipe must be connected to a

device expelling the fumes to the outside. If the

hood is to be used in filter version, then fix the

deflector F to the chimney support bracket G and

connect the other extremity of the pipe to the

connection ring placed on the deflector F.

16.Make the electrical connections.

17.Apply the chimney stacks and fasten them at the

top to the chimney support „G“ (17b) using 2

screws (17a).

18.Slide the bottom section of the chimney down until it

completely covers the suction unit and slots into the

housing provided on top of the hood.

19. Fix the lower stack of the chimney with 2 screws.

Remount the carbon filter frame and the fat/s filter/s

and check the perfect functioning of the hood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scholtes HDB 9 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info