Bedienungsanleitung Scholtes hp 95 (Seite 14 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

128412

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Operation e Maintenence

Operation

To start the hood (after following all the instructions

described in the previous paragraphs for the

installation and having taken all the safety

precautions), check which type of controls - among

the 2 types indicated below - your hood is provided

with and then follow the relevant directions given.

Push-button controls

The control panel includes:

· 1 “I\0” button to turn the motor on/off

· 3 “I” “II” “III”, buttons to adjust the motor speed

(1st - 2nd - 3rd speed)

·1 “

” button to turn the lighting on/off

Touch controls

The control panel includes:

·1 “

“ key to turn the motor on/

off

·1 “

“ key to reduce the motor

speed

·1 “

“ key to increase the

motor speed

·1 “

“ display that indicates the

motor speed

·1 “

“ key which, once

pressed, turns the motor off

after approximately 12 mins -

when the function is enabled, a

“

“ dot turns on at the bottom

right-hand side of the “

“

display.

·1 “

“ key to turn the lighting

on/off

ATTENTION:

Every 30 hours of use the microprocessor, which is

the heart of the system, indicates with a flashing “A”

on the display that the metal grease filters should be

cleaned to consent the exhaust to function better and

improve hygiene in the room. To cancel the warning

message after cleaning the filters, switch off the

hood, press and hold key n°2 for more than 5

seconds. When the key is pressed the letter “A”

appears on the display; after 5 seconds this

disappears and the microprocessor starts a new 30-

hour count-down before displaying the next warning

message.

Maintenance

Always make sure you carry out all operations with

the omnipolar switch off, in position O.

A) Cleaning

Clean the external parts of the hood using a soft

cloth and neutral detergent; and avoid using abrasive

powders or brushes. For dirt which is difficult to

remove, you may use methylated spirit. Clean the

steel parts by rubbing in the direction of the surface

finish.

B) Cleaning the Metal Grease Filter

Excess grease particles in the metal filter could

cause an increase in the inflammability of the same;

in order to avoid possible fires, the metal grease filter

should be washed according to how frequently it is

used (in any case every 30 days) in a dishwasher or

in lukewarm water using normal washing up liquid.

After rinsing it and drying it thoroughly, replace the

metal grease filter in its special housing.

C) Lamp Replacement

The hood can be provided with different types of

lamps: incandescent, halogen and neon lamps.

· Halogen lamps (fig. 5 and fig. 6): Figure 5

illustrates the type of lamp with a G4 cap, 20W

power and 12V voltage; to replace it, use a

screwdriver to remove the glass support ring “A”

(fig. 6), then remove the protection glass “B”; pull

out the faulty lamp and replace it with a new one;

then reassemble the protection glass, fastening it

with the corresponding ring.

Fig. 5

Fig. 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scholtes hp 95 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info